JessEmClear-Cut Precision Stock Guides, JessEm# 04215

I'm fairly new to router work, and can't help but think that I might have lost at least one fingertip if it weren't for receiving these little helpers.The price kept this on my wish list for a year or more, and although I sort of wish I'd held out for the Jessem Clear-Cut TS Stock Guides (they weren't available for shipping to NZ) I am pretty happy with these. They're solidly made, and do a great job holding my timber down close to the bit on my router table.

JESSEM Clear-Cut Precision Stock Guides are easy to install, work great, and hold the work piece firmly against the fence and the table. In my opinion, the stock guides work at least as good, if not better, than feather boards. The only down side, that I can see, are the urethane one-way rollers which wear out in some period of time depending on usage. They can be replaced and they don't have to be ordered from Jessem. I've see Jessem urethane one-way rollers available from other sources on the internet.

These do exactly what they say they do, hold your board down and against the fence and help prevent kickback, they work just like the table saw versions, same quality, can't ask for more. I have the kreg router table and as other reviewers have stated, once you tighten the knobs on the guides you can't slide your fence wings to adjust for router bit size. I added a nylon washer to each bolt and problem fixed. I used four of these Hard-to-Find Fastener 014973168735 Washers, 1/4 x 1/2

Decided to try these as I've found featherboards on the router fence more annoying than helpful. These stock guides are a definite improvement and make for a more smooth passage of the work across the router table. Build quality is quite good and the guide assemblies have a real heft to them. The t-track on my Kreg fence sits slightly behind the working surface of the fence, so I had to shim the guides with a washer on each of the t-bolts--easy fix. Without shimming the guide assemblies would tilt away from the fence along the bottom as the knobs were tightened. This is just a quirk of my fence design. A flush-mounted t-track would require no shimming.Only quibble I have is that my kit arrived with only one of the knurled knobs broached for the included hex wrench you might want to use for setting the roller height. For extended routing a bit of extra tightening can be a good idea to prevent vibration loosening the knob. If your hands are getting a little arthritic the added leverage given by the hex wrench can be a real help. This product packaging error is minor, and is the only reason for my 4-star rating, but I'm not alone here as I came across a few other complaints with regard to missing hardware or other product problems with JessEm kit while researching router lifts, tables, and fence systems. Given the costs, more attention to detail would be welcome.

I have A Incra system on both my table saw and my shaper, due to the lower profile on the Incra fences I couldn't use my various feather boards I own, and had to make my own which worked but I saw these and thought why not give it a try , and I could return them if they didn't work. Well they are an awesome addition to my. incra fences, infact I no longer use feather boards to push the stock into the fence as the offset rollers pull the stock into the fence with a nice bit of force. I had to run a 12' board through my shaper, and I always set up extension tables for this type of work as support. I have 2 sets of these Jessems, due to an order error, (not amazons issue- another mail order place took my order, lost it, and then shipped them to me after canceling my order) so I set up a pair on both sides of the fence - locked everything down and ran the board through with NO problem, it stayed tight against the fence. They are quick to adjust. Two cons, they aren't for stock over an 11/4" on my Incra fences and do not use the Allen wrench they supply to tighten it on your fence, I ended up causing a slight mushrooming on one my fences that I ended up machining out. 5 stars as they work as they are advertised!

Great quality. easy to install.

I have this device for mytable saw and love it. I tought it might be a good iedea to do the same on my router table. Unlike the table saw version, there is no adjustment to extend the rollers for wider stock and it is not spring loaded. Set up is a breeze and works realy well. I've never had an issue with kick-bck on the router but why take chances!

They fit my fence perfectly, made routing much easier and safer. Definitely worth the price.

Awesome

Gute 180 Euro für sowas ist heftig!Es funktioniert und das ist Sinn der Sache! Bei dem Preis muss aber auch die Verarbeitung stimmen und wie kann angeblich neue Ware, original verpackt eine 5mm Schlagstellen an der Kante haben mit abgeplatzter Eloxierung? Die gefrästen Taschen haben saumäsige Frässpuren!Geht zurück und neu bestellt! Update der 2. Lieferung folgt!Update: 2. Lieferung war besser aber immer noch nicht im Ansatz wertig!Hab noch ein Clone bestellt in China! Letzte Bild... Rot Gold bisschen speziell! Jedoch extrem gut verarbeitet mit dem gleichen Funktionen und Technik für 34 Euro inkl Versand...Gute Nacht JessEm!

jessum can doit!

Love this gadget.. stabilizes the wood 100%.. don’t hesitate…

JUST, PERFECT!