Dorman 924-251 Front Windshield Washer Hose Compatible with Select Cadillac / Chevrolet / GMC Models

Perfect fit on an 03 Silverado. Had to replace the pump and did this line at the same time. Can’t beat the price and ease of install. I had spliced mine three times. Didn’t realize these were available aftermarket for so cheap!!

This front washer hose fits many years Chevrolet Silverado - mine is a 2002. It runs from the washer reservoir to a connection just past the battery on the fender. Because it comes bent up to fit inside a standard box for shipping, you will need to adjust the over-bends. They need to be straightened a little to approximately 90 degree bends. This can be verified by looking at the old part before it is removed. Some people have mentioned using hot water or a heat gun to soften the bends. For simplicity, I used a candle in a glass jar. I held the over-bent sections about two inches above the flame and moved the part back and forth and rotated it as much as I could until it started to loosen each bend. I stopped when the bends were at approximately 90 degrees.Check online for advice on the labor to replace the part. I had dropped the part into place for rough alignment. I discovered that I was able to reach the elbow hose connection at the reservoir pump from under the truck by reaching up behind the bumper. I used a fork-shaped panel removal tool to pry the hose off, although a screwdriver may have also worked. My arm got soaked as the washer fluid started pouring out, but I was prepared for that and I pressed on the new elbow quickly. I may not have actually needed to remove the battery for this job, but I had taken it out already.Other purchasers have noted that the part did not last long for them. I just installed mine today. I will updated my review if I have any problems.Update 5/6/22: Since installing this hose last year, I have had trouble with it a few times. The rubber tip on this hose does not have a strong grip on the washer tank pump. It sometimes holds for a short spritz of washer fluid on the WS, but will likely pop off with a prolonged blast and leak all the fluid onto the ground. I’m thinking of tightening it with a small zip tie.3/18/24: Small zip ties on both ends of the hose worked for almost a year as the truck sat parked most of the time. When I needed the washer, the hose popped off the reservoir pump and will not reliably stay attached. Can’t find an AC Delco brand, so I will reorder this hose in hopes that they have improved the design since 2021.

Works great!

My hose on pick up ,rotted out up by battery, this is the correct hose that fits from washer pump to the connection behind fuse block. It comes all bent out of shape to fit in shipping box. You’ll need to heat it up a bit to straighten it out enough , I used a hair dryer. Some people say they put it into hot water to soften it up enough to bend into shape, connections hold well no leaks . I can now clean windshield again,

Contrary to the negative reviews, this is what you need. It comes bent up pretty tight in the box so it's easy to assume it's the wrong part. Give it some flexing (I didn't need to soak it in hot water or use a lighter) and it should expand out to its proper size and shape. It is hard tubing but won't snap if you flex it. I've included a photo of what it looks like after prep, install, and removal (as I had to take it out to install a new pump).Overall the install is a bit annoying (requires removing the battery tray and some clips) but it's well worth it if you have a blown wiper line.

I recieved this hose for the windshield wipers in 2 days. Installation isn't that bad. I would YouTube it. The hose was almost a perfect fit. So far I haven't had any problems. I would recommend.

It was a perfect fit BUT before I installed it I did have to SOAK it in really hot water and reshape it as it was in a smaller package when shipped and it was bent out of shape.. It took a couple soakings in almost boiling water to soften it enough to reshape it to original shape without taking a chance of breaking or crimping it.It did fit my 2005 Silverado Truck Perfect after that.Here in Texas Windshield Washers are part of the yearly safety inspection required for registration.

Worked great for about a year, and recently had some car work done near the pump and I don't know if the mechanic didn't know he knocked it off or it just came off itself, other than that it's cool for the money!

Perfect fit. Works great. Quick shipping.

Simple product, fit as promised, delivered quickly.

Exactly as advertised. Windshield washer works great again.

The tube is a hard plastic and to ship, is folded and looks bad. However with some gentle persuasion it installed well and works fine.

Part is, what it was suppose to be.