ESUPPORT Car 2" 52mm Water Temp Gauge Meter Temperature Light

Simple to install. I do recommend buying a 2 1\8 mount for the gauge unless drilling a hole in the dashboard is your thing. Simple to wire up one from the positive side and one to ground. Looks good and is easy to read. lets you know something is going wrong in your charging system before the light says the battery is dead.

please use automotive vac lines, do not use the hose in the kit. please make long 90 degree turns and prevent kinks. they are not 100 percent accurate but it gives a ball park of what the engine is doing.

This brand of gauges is modern with a Led backlit display that best matched the gauges my Mustang was equipped with. The gauges are a great value and the quality of construction is very good considering the price. This is where the good part of the story ends. The vacuum gauge was badly out of calibration by about 8-10 inches of vacuum! The oil pressure gauge was accurate but the sending units would fail after about 120 days! I bought another and the sending unit failed after a similar amount of time. I purchased a third and it too failed after around 100 days. THis means all of this companies sending units are garbage, and the worst thing about this story is that the company is clearly aware of this shortcoming of their products and do not care. This is a company that is intentionally building parts that fail right after the warranty expires . Only a dishonest company would build things to fail after 100 days. I wish a manufacturer of quality gauges made a line of gauges with a face design that matched my cars factory gauges, but there is none. Do not waste your money on this company's products.

Note this unit is in celsius .. easy enough to do your conversions and lay some paint or sticker marks. Is accurate against a under hood cap stat.. visible in bright daylight and mot overwhelming at night if choose to wire direct. Can easily be seen unlit daytime and wired to dash light control.. very satisfied

👍

I was looking for an electric temperature gauge with 270 degree sweep and a face marked in Celsius. This one fit those requirements and my desire for low cost.However - it has serious issues.#1 There is one power lead, so the lights turn on when the gauge is on. If it's wired to the dash lights, then the gauge is only on when the lights are on. If the gauge is wired to post-ignition, then the backlight won't turn off with the dash lights. Now this is probably a "feature" since the front glass is dark smoked.#2 The front glass is dark - so dark the gauge is unreadable without the backlight on. And it's not really bright enough for daylight and WAY to bright for night.I fixed both problems. I pried the chrome ring off the front which let me get inside. I cut a piece of clear plastic acrylic (plexiglass) to replace the smoked one. Now the gauge would be quite visible in daylight - but would be way, WAY to bright at night.Taking the gauge out of the case I was able to determine the backlight LEDs are connected with wires to the main circuit board - so I could have routed the LED "+" lead out the back of the gauge and used an external resistor to get the backlight to a useful brightness. But I dug a bit deeper and found that there are red LEDs for the needle and white LEDS for backlighting the face. I modified board so those are separate. I now had wires for ground, meter power, sensor, red LED, white LED. Using external resistor, I have the LEDs dim enough it works quite nicely at night, and with the clear front lens I don't need any lights during the day.After all this - it's a pretty nice gauge! With the stock sensor it does read a little bit hot.

I went ahead and bought the voltmeter and the O2 gauges from the same company. Seemed silly not to.This review will be for the o2 Gauge.The gauge was VERY simple to install, although I do have experience with vehicles. Do NOT expect this gauge to be completely accurate as it's just a simple one wire and not a wideband gauge.The main reason for my purchase was, in all honesty, looks. I needed the Voltmeter, but had accidentally ordered the dual pod.Do I regret the purchase? Absolutely NOT. The gauge is crisp and clear, not too bright, and very lightweight; almost to the point of feeling cheap.Just a word of caution: The wiring for the gauge is NOT the same as the diagram shown on the sales page. It has 2 extra wires (Switch and Dimmer)

Arrived in great shape(no box). It works great with my Simhub Arduino project. Very accurate gauge.

Superbe, merci

1. The gauge come with the set button missing2. He have 5 wires on it but instruction show only 3 wire red/green/black we found that the yellow was the illumination and white??? We don't know we test the white cable on everything he only do something on 12v when the gauge start up3. Everything is plugged but nothing work !!4. The oil pressure sender they give with the oil pressure gauge is crap !!!5. I contact them to let them know that the Oil pressure sender was crap and nothing was happening they said we can give you 5$ to buy another one !!!! What you want me to do with 5$ !!! A good oil pressure sender cost around 40$ to 80$

No trae el selector de cilindros 4,6,,8 solo un botón que dice set ?

Was installed and it worked for 3-4 test trails….and quit….I do not recommend this product