Ensenior 12 Pack 4 Inch LED Recessed Ceiling Light, Dimmable, 3000K Warm White, 750LM 9W 120V, High Brightness Canless Wafer Downlight - ETL&FCC&IC

So I don’t typically compromise on lighting. I’ve installed numerous conventional 6” can lights throughout our home with relatively costly LED trim kits and generally been happy with the results. When I stumbled upon these and realized they were about half the cost of 6” cans with LED bulbs, I crossed my fingers and bought 30 of them for our basement.First off, these are well engineered lights. Someone put a lot of thought into this design. They are very easy to install with simple tools. You will need 1/2” knockout clamps and that’s about it, save the wire, switches, etc.Most impressively, these can be positioned anywhere on the ceiling regardless of where your joists are located, but only on new installs (before hanging drywall). I pre-installed the ballast boxes before hanging drywall. Regardless of where you want lights or the locations of my joists, the lights will fit given how the clamping mechanism works. An example of what may perceived to be a problematic joist location is included in the photo. However, this is a non-issue for new installs. But, you cannot do this for a retrofit as the ballast box is a bit larger than the opening provided for some joist locations. For retro-fits you definitely want to be clear of the joists.Regarding light output, I’m pleased but I’m not quite sure they put out the stated lumens. I have cans of the same rated capacity at a slightly greater spacing in another room and the overall luminescence appears to be the same. I went with a 4’ by 4’ spacing in the photo and am happy with the results. Better to have too much light and dimmer rather than not enough.I used a 4-1/8” hole saw and it is perfectly sized for the job. The lights come with an integral gasket which is great if there is an uninsulated space above, but this results in the lights sitting not quite flush with the ceiling. It’s not objectionable but I’m picky. Since this was a basement rehab, I removed the gasket and they sit tight and flush with the ceiling. It’s a very clean look.The Lutron dimmers recommended work flawlessly, not a hint of flickering and they dim down quite low.My only suggestion to the manufacturer is to provide either longer cable lengths between the ballast and light or provide an option to buy extension cables. For new installs, the light needs to be located within less than a foot from the ballast. This was not an option for me in some instances so I needed extension cables which were very difficult to come by. However, there were relatively inexpensive when I finally located them from another vendor.All in all these are absolutely worth every penny. You cannot go wrong with these lights provided you plan ahead on new installs. On retrofits there should work issue and they would be ideal for drop ceilings. checked all 30 lights when they arrived and all functioned without issue. I cannot speak to longevity as my lights have less than 40 hours on them. Provided their longevity is a good as this product design, I don’t expect to ever have to replace them.

I installed these in our kitchen & living room, and they look fantastic. I sold industrial and commercial lighting for several years, and I’ll admit that I was hesitant to use a brand that I’d never heard of; however I couldn’t be more pleased with how these turned out. They were very easy to install, and the lighting quality, uniformity, and output is exceptional. Being able to adjust the color temperature is a great feature as well.One suggestion I would have for others that buy this light is to pay attention to the cutout size. I purchased an adjustable bit to cut the holes in the ceiling, and I foolishly assumed the hole was 6” since this was a 6” can. The instructions & template clearly noted the cutout needs to be 6.1”. I was able to make it work even after cutting the 6” hole though.

I love these lights. I added 6inch to my theater room and 4in my living room. I keep them on 2700 for a warm feel. Easy to install. Make sure to use 14/2 wire instead of 12/2. I had 12/2 laying around and it was hard to adjust the wire in the boxes provided. The springs are strong as well to hold the lights in place. 10 out of ten. I will be ordering more to finish the rest of the house. The Lights can get bright so I highly recommend a dimmer for them.

My house has the dated recessed can lights and I’ve hated them ever since we moved into the house. For 12 of these, I couldn’t pass up the deal when they were on sale. So far I’ve used 5 out of the 12 and I just love how easy they are to install. The junction box has push-in connectors and I’m completely sold on those and don’t see myself returning to wire nuts (unless the wires aren’t solid).Out of the box these are on 5k and are quite bright, so I put them on the lowest setting and it’s much better for the dining room area - don’t need intense light like we’re investigating something in Area 51. I definitely will be installing these in other parts of the house that has outdated lighting. Since I’ll need to cut a bigger hole in the ceiling for these, they made it super easy with a template that you can trace out the size of the hole if you don’t have a hole saw.Anyway, I highly recommend these if you’re looking to upgrade your lights with flush mount LED’s!

Pros:1. These are super easy to install2. can go anywhere, including directly under a joist because they are <1/2 thick.4. Great size5. Strong spring clipsCons:1. 14 gauge wire only, box is to small for anything else.2. Color temp is funky and they have lower cri3. I think because of the low voltage transformer some switches cause a flash when you initially turn them on.Overall these are good if you don't care to much what light you have and don't want to put the effort into getting something more advanced from DMF or Cree. The advantage with the Ensenior lights is they are super simple to install, don't require some bracket or housing. You just snap them into the drywall.You need to absolutely make sure you follow their guide for what switch to use. The dimmer switches you buy from home depot will cause issues I think. They will flash the lights when initially turned on. The actual dimming of the lights works great and their is no flicker but they flash. I think this has to do with the lower voltage nature of the lights and the dimmer switches assume high voltage lights.I would like to also add that their customer service is outstanding and if you have issues they will absolutely stand behind their product and help you make it right. Communication was great and very fast when I had issues with the flashing and strange color temp. My only suggesting is can they make a higher quality light in the same form factor. If they can do this and also increase the compatibility with some dimmer switches you can buy at home depot they will have a one of a kind product.

They were packaged and built very well. The gasket provided is kinda lacking and got stuck to the protective coating but other than that they installed easy, they don’t flicker or do weird stuff and they make my room look great. Overall very happy with the price and value!

Buen producto.

Easy to install if you have basic experience and knowledge. These run cool which is a very important indicator the LEDs are not wasting energy like other models do. The selectable color temperature puts excellent value on these fixtures and the range is wider than most offerings making these lights an even better value in comparison to others that are very similar and in the same price range. Overall, a great buy for me and my clients.

I love these things (12 pack 4Inch LED Recessed Slim Pot Light with Junction Box) 5 selectable color temperatures means you can select warm white to harsh white to match the room, dimmable and don't make any buzzing noise (but that might depend on your dimmer). So slim they install anywhere even if there is a joist right where you want to put one, these are getting installed all over the place in my house!! A couple of things that could make them even better -1. If the junction box was just an inch bigger it would make installation so much easier.2. Make sure the wire is properly seated in the wire splice block before cramming it into the box coz the wires can pop out - even better replace them with Wago lever locks which is what I did.3. Why don't they chuck in some 1/2 inch plastic romex cable connectors? - for a couple of cents each it would just be a nice touch.4. Buy extras / spares - they're cheap so grab a few spares for if/when some fail in case you can't get them anymore in the future.5. Get a good hole cutter and you won't regret it, I got the Milwaukee adjustable hole saw (C$35) and it's worked really well so far (about 40 nice clean holes).6. Don't skimp on the number you plan to install, with 8ft ceilings if you don't install enough you can end up with dark spots in your room, but this is the same with any pot lights so read up about standard spacing for pot light installations.7. Buy a good dimmer if you want to dim them, if you get a cheap crap dimmer switch you will regret it.Most of my comments above are just tips / advice and not criticizing the product itself, becuase these LED pot lights are fantastic.

A few things I like about this light.* 5 white colors to choose from during the installation to fit the ambiance of any room.* The springs holding the light to the ceiling are nice and tight.* Can dim the light to a very low level without flickering.* Nice bright 1050 lumens light.Be sure to choose the size you like, 6" or 4". I went with these 6" because I didn't need as many lights and easier to get your hand into the ceiling and even a drill if need be.I do find the 4" light a bit more subtle as far as décor goes.I rated these easy to install, however, if you are replacing an existing light you still need to remove the hex box under the existing light and be comfortable working with household wiring. Some existing hex boxes are more than a simple wire or two, The box that comes with the light can reasonably accept two 14/2 (maybe 14/3) wires. If you are unsure of what you are doing hire an electrician.