ubrokeifixit Gear S2 Back Door Glass Rear Lens Glass Case Replacement with Adhesive for Samsung Gear S2 SM-R720 SM-R730 SM-R732

There were no instructions, but I followed a YouTube Video. It was easire than I thought. The glass fit perfectly and was so easy to install once I removed the back cover and the broken glass. Now I can finally wear my watch again after 1 year of being broken and having issues getting it repaired by Samsung.

The case cover replacement was used on my SM-R720. The seal holding on the back cover turned to goo, thereby releasing the back cover. Since directions were not included with the product, I photo documented what I did in hope of helping others who may not be as mechanically inclined. For my purposed, the product did exactly what I needed it to do. I am pleased and would recommend. The following is what it did:With the cover off, I used the point of a razor blade to carefully remove the old black 2 sided tape. I then used rubbing alcohol and a qtip and paper towel to gentle remove the adhesive residue and clean surface where the new 2 sided tape would sit. I also used a paper towel and the rubbing alcohol to clean the back cover as it was covered in adhesive residue. (Since my back cover wasn’t damaged and had the model number, etc. on it, I reused it and discarded the replacement that came with the repair kit.)With the surfaces clean, I removed the clear backing from the new tape. I held the tape by the plastic tab in the middle of the upper backing, being careful not to touch the tape’s exposed adhesive on the bottom. After aligning the jogs in the tape with the watch, I carefully set the tape in place. (To make it align better I held the tape at a slight angle and pushed it up against the side of the tape channel on the watch, then lowered the tape onto the surface).To remove the upper backing, I gently pulled up and slightly towards where the tab connected to the circle of plastic. Once removed, I aligned the watch back cover window with the sensor on the back of the watch. I used the same technique to set the cover as I did the tape: held the back at a slight angle, pushed it to the side of the tape channel then lowered it into place. I finished up by gently but firmly running the plastic guitar pick around the edge (I also used my finger nail for good measure).Good as new. Hope this helps.

The product itself is great, I bought the used one as almost half priced, but honestly just as great, not broken or anything, only thing is you do not have instructions to work with. You can either do it on the surface, using the Exacto blade plastic to pry and clean off the wireless charger pad that has been adhered to the glass. However, if you are looking to open up the watch as I opted to do, then you need your own screwdrivers to open up the gear s2 and remove the glass, the provided tools are handy in removing the wireless charging cable and removing the wireless charging pad to be able to place onto the replacement glass. I wanted white the black looks pretty good too. Overall I give it a 4/5 I had the tools to open it so no issue from me but keep that in mind. Got it up and running in about 5 minutes, the adhesive gives room to work with as well as I placed it wrong but was easily able to make the hole for where the sensor checks heart rate. Up and working in the last picture.

This was super easy to install and so far works great (it's only been 2 months but it's holding on strong). There are no directions on how to install this so I had to Google it and I found a Reddit topic on how to install. I'm very satisfied with the product and would recommend.

Failed within 2 weeks

This came with tools but no instructions, so I sought help on You Tube but couldn't find the exact item. So I ended up putting it on wrong, which blocked the sensor's access to my skin. I had to then get a thumb tack to pry it off (adhesion works great BTW), and to my horror, the watch circuit board came off with it! Thankfully I was able to piece it back together and figure out what I did wrong with applying the cover and all seems well now. But instructions or even a link to a You Tube video would have prevented the whole mess.

the Samsung gear S2 have been my favorite watch and thanks to this purchase I'm still able to use the watch with no issue. saved me from having to buy a new watch

This review applies ONLY to the Samsung Galaxy S2 CLASSIC Smartwatch. I have no knowledge of any other watches or repairs.I watched a bunch of videos all claiming you have to disassemble the Samsung Galaxy S2 CLASSIC watch to replace the damaged back glass. I can tell you, there is NO reason to do this with this particular watch. I didn't even have to take off the band. I carefully used an Exacto-type blade to get under the broken glass from the back, peeled it all off, cleaned it up with an alcohol pad and installed the new glass. Done! Ten minute job and I was being overly cautious.One thing that may be slightly confusing (at least it was to me initially) was that the glass comes with a green (I think it was green) odd looking sticker. At first, I thought it was some kind of company logo or something. This is actually the double-sided tape adhesive needed to stick the glass in place. Be extra careful putting this tape on. It really sticks!The end result is a perfect fit and indistinguishable from the OEM factory glass. I hope this helps people tackle this very easy job and save yourself a ton of money. Thanks, ubrokeifixit.

Excellent produit, un peu compliqué a installé pour le reste fit parfaitement et tiens en place. Pour un produit partit de Chine, il est arrivé rapidement.

adhesive circle didn't stay on the back of the watch, peeled off straight away using the little orange tool.

Was under the impression that it'll replace the factory adhesive tape that gets worn over time. However, it quickly lose adhesiveness, and become no longer functional. The overall material isn't as robust as the OEM equipment neither. Recommend go get some B-7000 or T-7000 epoxy glue instead.