apiker 2 Pack Screen Protector for iPad 9th 8th 7th Generation 10.2 Inch, Tempered Glass Film for iPad 9 8 7 (2021/2020/2019), Case Friendly, Apple Pencil Compatible, High Response

This replacement screen worked perfectly for my iPad and saved me a significant amount compared to having it repaired at the Apple Store. It even came with a complimentary screen protector. Just be sure to go slowly, take your time, and watch the instructional videos — if you do, it should work as well for you as it did for me. Highly recommended! :)

This screen protector is fantastic! It’s a sheet of very thin but durable tempered glass. The package of two came with screen cleaner pads, a dust magnet and a cloth lens cleaner. Following the instructions, it was super easy. The sheet is sturdy enough to prevent air bubbles to form during the application. Once the protector sheet joins the iPad screen, it automatically adheres….i didn’t have to do anything or even touch it. No aggravation from trying to remove bubbles, straightening it out, etc, The next time I replace the protector, I’ll remember to capture a video. Highly recommend.

Value for money:This was a good value for this product. It is a glass protector at an affordable price. It is very sturdy easy to use and goes in smoothly.

It was fast and easy to put on compared to others I e messed up on first try cause others don’t work and come off fast right after you put it on the surface but this one was awesome easy and fast thank you

I'm using a 9th gen iPad, this screen protector kit comes with two protectors that look nice and thick and have the proper oleophobic coating as well as clean cut corners with proper bevels. They also give you special stickers to create a hinging mechanism to help you attempt to align this beast to your tablet screen correctly. Now the price is unbeatable and I think the quality of protector itself is just fine. I use mostly my hands and not really the stylus on this iPad but I have zero complaints with it applied to my iPad.The reason I took a star off had to do with the fact slightly incorrectly cut in one dimension and that causes a real dilemma during installation. If you look at the centering or offset of the hole where your touch ID fingerprint sensor and home button is supposed to sit you'll notice that the cut is actually off center a little bit. That is to say that if you mock up your fitment ahead of time by not removing the backing and simply placing the sheet on the tablet face to try to align it you'll see that it's incredibly hard to not have one of the sides of the cut out for the touch ID actually make contact with the metal ring. In my case it's almost like the cutout is shifted to the right slightly and therefore doesn't give you even spacing when you center all four corners neatly on your iPad screen. You have to actually push the bottom half of the protector over to the left a little more. So you're right and left sides do not have equal spacing the extreme ends of the screenNow this is a very slight difference, but if you align at the top correctly and then you go to align the bottom correctly you'll see that you often wind up with the entire screen protector skewed at a slight diagonal and that's because a lining the top with equal distance on the left and right does not result in a centered hole for your touch ID home button, you'll actually see that you are impacting your touch sensor with the edge of the cut out. So what you have to do is you have to very slightly skew the protector to make sure that that cut out stays outside the touch ID ring. Now I managed to do this but I've applied a lot of protectors as I used to be part of an IT helpdesk that did this for our clients. And I can tell you this added at least 25 minutes to my staging time. I'm not kidding. I had to dry fit again and again and again, due to the close tolerance of that home button cut out I would always wind up with the need for the hole to be off-center so you couldn't just make everything equal distance on the touch ID button and the perimeter of the glass. Unfortunately you need to be inside the perimeter of your glass because else if you touch the outer portion of the case with the screen protector you'll lift up the protector causing a permanent bubble and visual issue with your installed screen protector. So you're going to have to skew the protector slightly if you find you have this whole cut out offset.As I said it's incredibly slight so if you can skew it slightly and stay within the bounds of your screen once applied, and I did use the tape hinging mechanism they advise in the instructions, I got a result that I can easily live with that I felt looked good. I was also able to do it in a way that kept all the major debris out so I didn't have any hair or other lint under the screen protector after all that work was said and done.I have no problem recommending this protector as a matter of size and the material used. But the cut out has a problem around the home button and that tolerance will cause the installation to require much more fine detail and finessing. If they had either made the home button hole slightly larger or if it was centered correctly instead of being off to one side improperly then simply giving yourself equal spacing around all these parts would've probably taken no more than 15 minutes of prep and application. As it sat this took way too long to do it right the first time but I got there. If you're someone that has a lot of experience putting on screen protectors on large tablets you'll be OK. If you're a first timer then you really want to go with somebody else's cut out to give you more spacing and therefore more margin of error for installing the screen protector.

I won't ever have a screen protector on one of my Apple devices without it being a glass one. They have saved my ass more times then I can count. This fits great on both my husband's and daughter's iPads. Screen coverage is nice, and the adhesion sticks very well. Applications, I will say, are not the easiest because their recommended way of doing it really isn't the best. But overall, the quality is really good, and I have been very happy!

“It worked perfectly. I followed the instructions and only noticed a couple of dust particles. I lifted the protector, used some tape to remove them, let it fall back into place, and the dust was gone.”

Worked as expected.