Nuvo SF77/188 Three Light Vanity, 18 in 3, Brass-Polished/Cast

Best investment I've ever made. I followed Simply Sandra's tutorial on YouTube and it came out great!!

Looove them ! Exactly what I was looking for and it made my vanity complete <3

I purchased 3 of these for my DIY Hollywood vanity mirror...good quality, I love my new vanity.

I havent installed on wall yet, but i put it all together and works perfect.I did not install it into a wall fixture, rather a Craft Light Plug with a switch for easy on/off, also purchased on amazon (amazon recommended it as a frequently bought together item); it has 2 exposed wires on one end.Full instructions that i wish would come with the light:To remove backplate from front plate, grip chrome bulb covers that would sit at bulb base and slightly twist or just pull; the covers will slide off exposing just the bare ceramic; once all 4 are removed, youll be able to remove front plate.For the plug, the plug wont match the instructions; the plug will have two white wires and the light has a white & black. If you look closely at the two white wires one is grooved and the other is smooth. The smooth one is your black wire, the grooved is white. Very important; your light wont work if you get it backwards.Pinch your two wires closely together and insert into orange wire crimper thingy; once your wires are fully inserted, firmly pinch your two wires at topto keep in place and keep twisty orange piece over and over until it stops or wires want to bend with it. Repeat for other set of wires. To test pull on wires to make sure they dont come out and are very firm and tight into crimper.Seperate your black wires from your white wires into seperate sides of box; you want to do this because if any copper wire inside your crimper is exposed and touches exposed wire from the opposite colored set, it could potentially start a fire, so just seperate them for 100% safety.Run your plug wire along the edge and have it coming out side of light.Take the green screw and screw it half way into spot marked ground wire. Take your ground wire thats attached to front plate and make a small hook on end of it. Hook the ground wire around the ground wire screw on light back plate, and screw in the screw the rest of way to tighten the wire firmly behind the screw.At this point, it is fully operational and you can test it by screwing in a bulb and making sure it works. Once verified, remove bulb, put the front plate into place the same way you removed it, remove the blue protective film on the chrome, and put light base pieces back in place. Once you remove film, be mindful of fingerprints. It will look identical to when you first opened box, just with a wire coming out the side and no longer has the blue film on it..Take the small silver screw and put into small screw hole on side of unit; this will help keep it secure so the front/back plate cant come apart unless you remove screw.Screw in your 4 bulbs; some of mine were a lil cock eyed so i unscrewed the bulb and adjusted the ceramic base a tad to align it correctly then put the bulb back in. Hang up, and enjoy!Another note; i plugged a remote sensor box in and plugged this light into it, then put velco on back of remote and attached it to front of vanity so i didnt have to reach go turn off/on, just a nice simple click of a button. The remote sensor plugs into a single outlet and has 2 plugs on it. This leaves one outlet with 2 plugs for the remote, and one normal outlet open for non remote functions. I got a surge protector and plugged my curling iron, hot iron etc into it and then used this for the other port on the remote sensor; so when i use the remote off button for my light, my curling iron etc all turn off and i eliminate fire danger that beauty causes lol

Absolutely love it!!! Wayyy better than the one from Ikea! It's really thin and shiny which is exactly what I was looking for

We used these fixtures for my wife's vanity. There are sources that describe the best lighting but trial and error was the best method. We started with two, one on each side, but found a bit of shadow so we took care of that with one more over the top.These aren't expensive but they are simple so they shouldn't be. The first two were missing the hardware but Amazon's great customer service took care of us.Installation requires some drilling and electrical wiring. We used a dimmable switch which can be helpful to prepare for different times of the day. The bulbs are 40 watt incandescent and are slightly warm in color. This many bulbs can make the room slightly warm as well. We thought about putting each fixture on it's own switch but there hasn't been a need for it. The height of the mirror and lights are set to where she can sit on a stool.The most important thing is that she loves it!

Great! I used them to Build a Hollywood style Vanity for my Valentine

I purchased two of these fixtures for my DIY vanity project. They were exactly what I was looking for! No, they do not include light bulbs (what light fixture comes with bulbs??) and yes, they are designed to be hard wired, so you will need to do a little "electrical work". A simple google search will provide you with all the instructions that you need (contrary to another review, you do not need to be an electrical engineer).