FGD Fender Hash Stripe Graphics Decal Sticker Set Universal Fits Car Truck or SUV (Hm01) 11"x23" (Red)

These come with instructions for a dry install. When I applied them dry, I ended up with tiny bubbles over a few areas. And since it was dry, I really couldn’t adjust it very much, so I took them off.The 2nd time, I did a wet install, which was much better. I wiped the fender with soapy water and used a clay bar and alcohol on it. Then I sprayed more soapy water and laid the vinyl down. I actually cut the decal in half lengthwise so I was putting on one thick and one thin stripe at a time. It was much easier than trying to lay the entire decal.After I squeegeed all the water out, I carefully pulled off the transfer tape. They were laying perfectly flat and smooth. Do not run a squeegee on the vinyl, only on the transfer tape or you’ll scratch it. If you need to work out bubbles after pulling off the transfer tape, use a soft cloth or microfiber towel.These are nice decals with a glossy black finish and they really accent the vehicle well.

Looks good! I believe many of the bad reviews done here didn't research on how to apply an automotive vinyl decal correctly. This is my first attempt at striping and didn't want to mess it up. I would highly recommend watching you tube videos on applying vinyl car decals. I watched about seven and rewatched a few several times before attempting this. I went with the wet method and did have to move the decal around quite a bit to get the creases out.I still ended up with a less than perfect install (A couple of minor creases), but am very pleased with the look non the less. The imperfections from my first go with this was negligible. Any way do your homework BEFORE putting these on your car!

I'm am such a DYI klutz, that I was so sure I would screw this up!!! But after reading the instructions a dozen time to make sure I understood, I got my masking tape, scissors and my car window ice scraper tool and tackled the project and voila! I was surprised how easy it was and it took less than an hour to apply it to my freshly-washed car. The only challenge for me (and it's noticeable closeup) is when the decal has to go around the curve above the wheel; it left minor creases. Overall, I am very happy with how it adds a pizzazz to my Prius C. I will be interested in how it holds up when the car is washed again.

The media could not be loaded.  Looks great on my car! Depending on how you use this, you potentially have a lot to work with. I was able to customize it even further and utilize it for both my fenders AND the back of my car (see video for details on the back). The key to applying your decal is precision, lots of pressure, and a good measure of patience. I didn't use any soapy water to aid in the application as many usually suggest, but that's mostly because I already have experience in applying decals and vinyl. I would recommend the wet method if you want to reduce chances of air bubbles or if you're new to applying decals. This was my first time applying a decal to two different surfaces (metal and plastic) at the same time, but the result was almost seamless!

Got this for my white 2019 Traverse Redline edition. Thought fender stripes to match black wheels with red stripes would look really sharp. I was right. However, these aren't real easy to install. I spent some time "fitting" them before I began the install. One needs to be patient, go slowly and pre-plan carefully. Even though seller gives complete instructions, I would suggest you look at YouTube videos first. In my case, wasn't real happy with my initial install effort and obtained 2nd set.

Applied graphics to both sides of the truck yesterday and from a distance it looks great. However, up close it looks horrible from all the air bubbles that got trapped during application. Used a squeegee on one side and my hand on the other side to try to reduce the air bubbles, along with using soap and water like the instructions suggest. The paper on the outside is so thick, that it's hard to judge how well it's actually being applied.

I used them for my 2019 traverse , they last me two year , ordering a new set and replacing them now . Good product , 2 years is not bad .

Went on Great! It says light soapy water but I us2d decal lube instead and it went on great.had a com small bubbles in decal but like it stated on the paper after a good day in the sun they all disappeared and looks awesome.The sharper the fold the easier it is to pull off when ready.But like it says don't get the paper wet or you will have a rough time getting the decal off.

The stripes were perfect and looked great for 6 weeks .. then started to fade and peel .. great idea ... poor product

Item not as described !!!!Good quality but I only received 1 strip and it was folded in 2 spots and flattened not good.JUNK, in my opinion !!!!