Spartan Mountsfor Mag Wall Display - Firearm Accessories, Wall Mount Display for Gun Room, Magazine and Ammo Storage and Organization, Black

I have used various wall mounts for my .556 magazines and really like the mount concept. The problem was I could never find wall mounts for my 7.65 x 51mm (.308) magazines until these Spartan mounts came along. These Spartan mounts, though they only come is three mag configuration, are really nice. The mounts are 3D printed, and finish is quite good for a 3D printed item. The mounts are easy to install, and are very sturdy. I currently have 8 of these installed and they are really nice. One additional note, Spartan makes a huge array of specialty mounts, once you get their product, or go to their web site, you will find almost any mount you can think of.

Fits 30-40rd Gen3 MagPul .556, but I changed hardware for bolts & nuts with washer for my safe door. The screws would have stripped out of the door cover. Could used a taller base to stabilize the unit against the surface its mounted to.

Excellent quality however a bit expensive, there are others on the market that hold five S&W MP15-22 mags for half the price.

Made very well. The 556 p-mags fit perfectly, very easy to install, even comes with good solid hardware.Definitely will order more.

Securely holds your AR magazines.

Solid unit that does what it's advertised to do well. The only option I've found for mounting ruger BX25 mags so there's no doubt they can charge what they want and people will buy (obviously I did). But 20 bucks for a small piece of 3d printed plastic is excessive. I would buy a lot more if the price were even remotely reasonable

I saw the other review that said total garbage and I ignored it. I purchased it anyway thinking there is nothing to it. What could be garbage?Long story short, I am glad I did. It isn't fancy there is no shiny chrome, but it is functional which is about all I care about. It is a 3D printed PMAG holder. I can't stress that enough so I will say it again. It is a PMAG 5.56 holder, not just any magazine will work with this. IT IS FOR THE BRAND PMAG .223/5.56!Now that that is out of the way lets talk about the picture shown. If you hang the mags as shown with the curve to the wall it will not sit right unless your wall mount is screwed to a 3/4-1" board. If you spin them around so the curve is out they sit nicely in the holder. Another 3/4" of molding behind them would make it work either way. (Suggestion for the Manufacturer) That is the reason for the 4 stars vs 5 stars. Also minor side note: there was one minor sharp edge I fixed with my pocket knife.I am sure someone will read the above and say something like if you hang them curve out the bullet is facing the room, that is dangerous. I am about as worried about that as I am worried about my gun getting up and going on a shooting rampage on its own. If anything it is probably safer because the primer is not available to be struck by something hitting it. With that said, I don't leave all my mags loaded so it doesn't matter. It is hard on the springs to leave them loaded. Buy a quality speed loader and you won't either :) Leaving 1 loaded to protect your house and family only seems paranoid until you have to use it, then it just seemed smart.I don't need to add a disclaimer as I don't work for them, didn't get any discounts, wasn't paid to write a review, and don't have to be to be a satisfied customer.Update (4/21/2018): I upgraded my rating from 4 stars to 5 stars and here is why. I just moved my mount to a new location and realized I was a little hard on them about the angle. There is a light angle on the back of it when I initially installed it apparently I over-tightened it and it pulled that into the sheet rock some lessening the angle. On my remount I was a little more careful and it seems to be a tad bit better. You can hang a mag as shown, it isn't perfect, but its better than before.

Easily to install!! Cand hook several together. Need to get more for my ar 10!!!