BLACKHAWK SERPA Quick Disconnect Kit (2 Female/1 Male), Coyote Tan

So, I ordered two of these sets for my taser. They were kind of hassle on the first set because you need to have the correct screw for the correct adapter otherwise it’s just spin (they all look the same but if your spins try a different screw until you find the right one). I wasted like 3 hours on this until I figured out that little nugget… then it took about 5 minutes to assemble the second set.I ordered two because I have two external carriers (one brown and one black) and also the belt attachment. I put a female adapter on both vest carriers, my belt teklok, and my backpack (molle). I have put one male adapter on my Blackhawk taser holster, and the second male adapter is currently not being used.This has made swapping carriers and/or where I carry my taser a breeze. Swapping carriers is always a hassle and this just makes like so easy. Well worth the money! No more dinking around with moving the molle panels and/or removing the holster from it to put on my belt.I plan to order a set for my firearm and attach one to my nightstand and one to my car (separate holster than my duty holster).It’s my favorite Blackhawk accessory because it’s so versatile and makes life so easy!Oh, PS, super easy to go from straight draw to canted draw.. just adjust where you place the male adapter before securing it into the female adapter.

I redid my CCW holster with this attachment and I love it. Its so much easy to take off and put on instead of having to take off the whole configuration when you want to sit back and relax. And when I need to get up and go it just reattaches back on. I love it!

Positive is I really love the design, super sturdy and this allows use on different belts/vests or mounts.Negative or more of a suggestion is the mounting screws that are included need to have a screwdriver slot on the brad female as well as the screw head and a rubber washer should also be there since not all places to mount are the same depth and the included screw female end are impossible to hold tight when in a recessed area, I replaced all included screw sets(much better). The only other downside is there is only one male included so fine if you own 1 pistol, However I own multiple and now own more than one set of this kit. The Serpa CQC is the Best design I have seen even with the minor Issue.

This is a good way to make your Serpa holster adapt to multiple mounting solutions without turning having to unbolt it every time.I personally have a molle mount for my plate carrier, a paddle for on my hip and a mounting system for in center console of my truck.Within seconds I can detach the holster from my hip and click it into my truck mount or my plate carrier. All it takes is pulling the two small spring loaded levers and twist it about 10 degrees.The kit comes with two female pieces and one male piece but all pieces can be purchased separately too. So if you want to switch between 2 holster (for 2 different pistols for example) or between more than just 2 mounts, it's possible if you buy extra pieces.The only downside for me and reason why I only gave the kit 4 stars is that the quick disconnect adds an additional half inch between your mount and your holster. this makes it tilt or sag on my plate carrier and adds a tiny bit of uncomfort when carried on the hip with a paddle.Overall I think this is the best and cheapest solution to adapt your serpa active retention holster to pretty much any blackhawk mounting system in seconds. No need for multiple holsters any longer.The installation took only a couple minutes. 3 bolts for each piece. It takes longer to decide in which angle you want to mount it than actually doing it.I also wrote a review about the blackhawk serpa holster that i've had for quite some time now. If you click on my name above this review you can easily find it in my other reviews.I hope these 326 words helped you out and answered some of the questions you had. I dare you to count them :-)Please feel free to contact me if you have questions.Pictures will follow soon!

Cumplió mis expectativas!!!

If you have a belt holster and want to use the BH Molle adapter, then this is the thing to get for those swaps between belt and, say, external pack. A very handy thing to have and allows for shifting of arms between preset pieces (belt position, shoulder position, MOLLE, etc.) for each that you have. Fast and intuitive to use with a press in and slight turn to lock in place and then a press down on tabs to remove.The included screw fasteners are difficult to insert by hand. I utilized a brass drift punch (flat surface punch) with a surface larger than the screw hole to push the receiving end of the fasteners into place. This was done by hand as the punch was basically used to do what my fingers couldn't to get some pressure on them to get them into the holes. I also had some worries about the fact that on one of the holes the receiving fastener or female end, was turning slightly and not allowing for a tight and secure mating. To alleviate that I utilized #8 lock washers, which proved to be so useful I backed out all the fasteners and used them on the male fastener or screw side to give a firm seating of the fasteners. The lock washer pushes against the head of the screw, thus putting friction on the threads and allowing for a tight mating that then has internal tension to keep things in place. Wavy washers could also work for this.Overall if you are going for BH equipment and need to move weapons around between positions, then you really can't live without this.What I wish was available was something to allow the use of other manufacturer's equipment via a round mating panel that would then insert into the male side of the rig. I've got a TDL holster that is just a little bit off on the hole pattern and a perforated kydex adapter would work like a charm to allow for cross-manufacturer swapping for those specialized pieces that BH just doesn't make.

If you have a SERPA holster, get this to use for transitions between your systems. Never failed me and I’ve used it tons in combat and for personal use.

Reçu avant la date fixée, je suis plus que satisfait

Perfetto fa il suo lavoro

Pretty solid kit. Having two female parts rather than two male parts is beneficial. It's good being able to not have an empty holster sitting on my chest when I'm not carrying. The mechanism doesn't allow for much fine tuning of the angle of the holster but luckily one of the set angles works for me. I can reach and draw much faster with this than with a belt holster, particularly with a molle tac vest.

Set up is simple. A little thought needs to go into how you plan on using your gear. Durable design and functional.

Gewohnte Blackhawk!-Qualität, einfach zu montieren, Super System, es gibt viele Anbau- bzw. Zubehörteile dafür, macht was es soll, echt praktisch, selbsterklärend