High Quality HP TouchPad Clear Screen Protector Guard Bundle (3 Pack)

Very hard to cleanly place but once on it is a really good cover.Here is what I did to place it on very cleanly.Prep before steps 1-4: Get one screen protector, lint-free pad, paper card from package, and clear tape roll and brown tape. Also grab scissor in. I used electric tape in place of brown paper and it worked too. If you have to use restroom as dust-free area by showering, also grab plastic bag to protect your tablet from steam.(This steps is before you bathe if you decide to do it this way)1) Pick a nearly dust-free area.2) Remove case if any, then clean tablet screen - at this stage it do not have to be perfect but there should be zero oily sheen but little dust is fine. Leave case out till completed all steps.3) Grab screen protector and align it on tablet, but DO NOT REMOVE any covers on it. Tape it on one long side with in least 4 brown tapes so it will be able to act as "door". It should be able to flip up and down without getting misaligned. Yes, it means you will have tape on touchpad itself. Be generous and use 3 inches each point on one side. Two inches on screen and in least one inch overshoot and tape on touchpad. So it will not loosen and cause misalignment. You can clean tablet after you're finished anyway.4) Put 2 "handles" on other side corners by partially folded over tapes. It should not stick to tablet at all. This is so you can easily lift it again without actually touching cover at all.(If you went for steaming room to get rid of dust, first put tablet in plastic bag, seal it so steam cannot get in, then bathe. Have fun bathing. Do not open restroom door and turn on vent till completed.)Prep before next steps: Make 3 or 4 segments of clear tape for use as dust remover. Tape it to something so most is hanging off edge.(if bath method, take tablet out of plastic bag)5) Now this is when you want perfection. Lift screen like door upwards, use close light and lint-free cloth to really clean the screen on touchpad itself. Wipe the bottom sheet of screen protector, wait while tiny amount from that settles on touchpad, then wipe touchpad again, seeking perfection.6) Now, with very clean touchpad, hold on one of handles as you peel off the bottom sheet off the screen protector.Never, at any point, touch the screen protector bottom or edges! This is likely cause your screen protector to get dust/oil from fingers!7) Carefully lower cover on touchpad, use both handles. You should try to avoid creating any bubbles. There is 2 kinds, ones caused by uneven landing and other by dust. Dust ones is usually smaller. You can lift it up again using tape handles and use one of clear tapes to pick up dust off screen or cover sheet. Clear tape is much stronger stick so it will grab dust even off cover sticky side.8) You should have cover on completely, and it should be mostly air-free. Don't remove top cover yet, you will need it to protect cover from paper card and your fingers as you rub near center air bubbles out. Rub cover under tapes that's acting as hinges outward so there is less air bubbles hiding under it.9) Carefully peel the "hinges" tapes from tablet but not the cover side, leave tapes there.10) Finally remove the front protective sheet from cover, taking tapes off with it.(if you are in restroom after bathing, you can now leave, taking stuff with you to more comfortable area)11) Carefully push any remaining air bubbles out to edge using fingers (not nails) only. If it is dust type it is basically too late since you have no safe dust/dirt free way to lift screen again. But luckily you can get rid of nearly all air out of it by rubbing air bubbles to edge from few different directions, leaving pretty much nothing but dust speck there. My tablet had 2 of those and it is pretty much invisible.12) Finally clean the touchpad tape dirt off it, then when touchpad is clean again, place it back in case again, if any.Enjoy the nearly perfectly placed screen protector on touchpad!

Hello future hp-touchpad-screen-protector-owners! FIRST OF ALL, A BIG THANK YOU TO THOSE WHO TOOK THE TIME TO WRITE RECOMMENDATIONS!!! I followed the advice given regarding applying the protector after someone took a shower. I've only used 1 and it shall remain like that.YOU CAN'T BEAT THIS DEAL, SHOP AROUND and SEE FOR YOURSELF :) You get a 3-pack for like $5, dude, c'mon!ORDER THIS AND DO THE FOLLOWING:1) Have someone in your home take a shower and put a towel at bottom of bathroom door to keep as much moist inside the bathroom.2) Have your stuff ready! Take out one screen protector, clean your touchpad's screen using your own breath and lint-free cloth (e.g. clean cotton shirt) and make sure it's clean :), get a card (driver's license, credit/debit card etc because you'll use this to use as a squegee.3) Once the person is ready to come out and you are ready to go inside the steamy bathroom, swap! Make sure you also put towel at bottom of bathroom door to keep as much moist within. Note: It may get a little warm in there that is why you want to have all of your stuff ready and know what you are supposed to do because you may start sweating.4)Wipe down one last time your screen and make sure that your hands are also clean; place touchpad on straight surface and one note that on the actual protector there are 2 little stickers that say "remove before/after applying"5) Remove the one that says "remove before applying" and place as centered as possible as you can. THIS WILL BE A LITTLE CHALLENGING, DON'T WORRY! ** Mine is not 100% straight, it's like 98% ok and that's good enough for me, however, I do want to stress that you should NOT STRESS over this. Keep in mind that you can USE THE CAMERA lens (little circle on top) and the button on bottom-center to help GUIDE THE POSITIONING OF YOUR PROTECTOR. (this is the hardest part, I had to re-do it like 15x's! lol6) Once you are pretty satisfied with it's positioning remove the other little sticker ("remove after applying") and then use your card as squeegee and gently yet firm, push out the air bubbles from center to edge, where you begin does not matter.7) try to get as many out, however, at best, you'll get about 95% of them out, the remaining %-age will come out by themselves within 2-3 days, assuming you did your best trying to remove at least the obvious/bigger ones.THAT'S IT MY FRIENDS!!! ENJOY YOUR AWESOME PRODUCT-PURCHASE :) God bless :)

Clean the screen with a humid paper towel, them dry it. Use the provided cloth and polish the surface clean. then take a large adhesive tape and cover the entire screen, gluing the tape, removing it and then moving to the next area, until you cover the entire surface. THIS PROCEDURE WILL REMOVE ALL DUST RESPONSIBLE FOR FORMING THE AIR BUBBLES! After that, remove the tab that states it needs to be removed before applying the screen protector, then carefully position it on the touchpad screen while aligning the camera, the home button, and the edges. Let the film alone for a small period of time and watch the film while it settles on top of the screen. Large bubbles will become small... when the settling process is completed, gently massage the bubbles towards the edges. Combine small bubbles into large ones before starting the migration. This process took 3-5 min for me. Not all bubbles will disappear, but you should stop when it seems your efforts in migrating the bubbles to the edge stop to bring results. At this time peel the other tab that states it needs to be removed AFTER the install. YOU WILL NOW BE SURPRISED FOR A 100% BUBBLE FREE protected screen. The small bubbles in the end were not located between the film and the screen, but between the film and the external film layer that was meant to be removed after the install... Enjoy now a touchpad that does not get fingerprints on it like a magnet would.