Illuminate Your Space with Confidence! 💡
The BJB 10 Pack of UL Listed Non-Shunted LH0567 Medium Bi-Pin Snap-In Rotary Locking Fluorescent Lampholders is designed for rapid installation and retrofitting. With a robust polycarbonate construction, these lampholders support high voltage and wattage, making them ideal for various wrap fixtures. Each pack contains 10 units, ensuring you have the right components for your lighting needs.
| Brand | BJB |
| Material | Polycarbonate (PC) |
| Base Type | Medium |
| Voltage | 500 Volts |
| Wattage | 660 watts |
| Specification Met | UL |
| Manufacturer | BJB |
| Part Number | 26.307.1023.50 |
| Item Weight | 1.58 ounces |
| Package Dimensions | 4.5 x 3.2 x 1.2 inches |
| Is Discontinued By Manufacturer | No |
| Style | Retro |
| Item Package Quantity | 10 |
| Type of Bulb | Fluorescent |
| Switch Style | Rotary |
| Batteries Included? | No |
| Batteries Required? | No |
F**Y
So happy to have found these tombstones, worked perfectly, now I can do my LED change over in my shop.
Exactly what I had been searching for. My fluorescent fixtures in my garage/shop had tombstones that pushed and locked in. I ordered 20 (2 orders of 10) of these the first go around because I was 98% sure they would work, but not 100%. Well, after receiving them (a lot quicker than the Amazon estimated arrival) they did the job. I searched for quite awhile for these buggers. I didn't want to have to modify my existing fixtures, and I sure the hecks didn't want to replace them. I have 15, 4 bulb (T8), 2' x 4' fixtures in my shop, and I'm converting them all to LED. It was hard (for me anyways) to find a snap in non-shunted tombstone. Very happy to have found these! In fact, after this review, I'm ordering an additional 3 packs of 10 (30) more, so I can finish the LED change out.
M**E
Perfect fit, quick install
So happy to have found these on Amazon. I looked all over the internet for this particular tombstone and could not find it anywhere. I was almost ready to buy a whole new fixture. Used these to do a ballast bypass for LED tubes. The fit was a little tight, but it worked. Was convenient having push-in terminals for the wires. Each side also has an extra terminal so that you can run a jumper wire to the next tombstone. My LED conversion in my garage is complete. 5 stars
D**E
Great, well made replacements for LEDs
What I liked: for rewiring a number of shop lights to LED, these were literally the only option I could find. Sure, they were a bit pricier than some of the others. However, they saved me quite a bit of money anyway and seemed to be higher quality than what I replaced. Tip: if you buy LED’s that only need juice at one end, you have to buy half as many of these.
C**S
Great Product
These worked really well. In changing over from fluorescent to LED 48" bulbs, I ran into just one fixture in my house that uses this type of tombstone, so I was apprehensive about the locking pin locations, dimensions, etc., but these worked perfect.
B**B
This is the one you want.
They do the job just fine. They are somewhat difficult to install but with a little extra work they will work, don’t give up.
R**Y
non-shunted
this is the only place I could even find this particular tombstone. It worked well for my application. I ordered 2 new fixtures, they came with the snap-in tombstones and in each fixture a tombstone was broken, but I had already planned to do a rewire, so the non-shunted, snap-in is what I needed.
D**T
did the job
did the job when i rewired a ballast -- the ones the "made-in-china-" light used broke. Now i have a new light and it only cost me a few bucks
M**Y
Toom stones!
These sockets worked well in the lighting fixtures. They were used to convert a fluorsent fixtures to LED.
Trustpilot
4 days ago
3 weeks ago
