WEILEITE SOLD OUT

Bought 2 since I own 2 jeep cherokees. Took 1 to shop for coolant leak and radiator was replaced. Mechanic found the oil cooler was leaking and quoted 950.00 to replace it. I replaced 1 that was leaking. Quality and fit seems good but I made the mistake of not replacing the sensors before install.its been 13 days since install and although seems to be holding up well, car threw a po298 code for high oil temp. Oil and coolant levels are good and no leaks from cooler. Will be tearing engine apart AGAIN to replace temp sensor. You can bet that when I replace the other cooler, I will replace the preinstalled sensors before install. All in all I figured doing this job myself saved about 1700 on 2 so I'm ok with that.UPDATE: Decided to reset the code and see if it came back. I'm happy to report that after a month, the sensor is working properly and still no leaks. I have upgraded my review to 5 stars.This saved me a ton of money and was an easy install. Recommend to anyone.

Great product! Installed on my 2014 grand caravan in December of '22. 3.5 years later and its still goin strong. Haven't had any leaks or issues yet. I used the seals that came with it. If I was doing it again I'd probably buy better seals separately and Install those but....I haven't had any issues with the cheap seals that came with it. Yet...

Got about 300 miles on mine so far. Being a mechanic myself I usually allways try to go with OEM parts over aftermarket. But the price difference was to good to pass up. A new OEM oil cooler from jeep is about 500 dollars. However if you have a seal that casuing your leak you could allways just replace the seals and keep your OEM oil cooler. But I was curious to see how this one worked, so I went ahead and bought the whole unit. As of yet there is no leaks. But I do recommend keeping your OEM one just in case if the aftermarket one fails and replacing the seals. I also installed this myself so I can attest that the fit was perfect. All the seals lined up and was completely plug and play. I will update this review if I run into any issues. But so far I definitely recommend.UPDATE:Still running great, car is holding the same coolant I had put in 6 months ago back when I bought this part, never had to fill the overflow a drop. Totally leak proof. A major thing I recommend is spraying those seals with white lithium grease before installing the oil cooler. People are blaiming the part when in reality its probally because they installed the oil cooler dry. Those seals have to be greased up good to make a good seal and slide into place.

The plastic one that was on was leaking a little and wanted to be proactive about it. I ordered this and the unit seems well made and solid construction. One thing I would have done over is removed the sensors and installed OEM ones. ONE thing I did do was use some black RTV on the O-ring-to-housing surface as it's not machined and possibly prone to a leak. I also went with OEM seals. I see videos online of people having a large amount of oil/coolant in valley when they go to pull the old one out, I didn't have this problem, pull it into the garage, let it sit overnight and pull it the next morning, you'll have zero cross-contamination, you'll get a little oil/coolant in the valley but nothing that will fill it up! I also changed the plugs while I was in there. Use the proper E8 socket! Torque to spec! I think it was 89 in-lb. You will have to do a little bit of fenagling to get it in, but it will go, no force!!1) RTV seals into the bottom of the housing (do this days prior to allow proper adhesion, also, clean the surface where the RTV is going with brake clean)2) let vehicle sit overnight to prevent cross contamination3) USE OIL ON THE O-RING TO EASILY SLIP THE TUBE IN THE HOLE! (not sure why people don't do this simple thing)4) Change the plugs while you're there, I don't care if you changed them 20k miles ago, change them! It takes 20 min.5) It's been almost 2k miles and no leaks and oil pressure and temps are fine.

Very nice, this is the second one of this brand I have bought. The first one is still going strong after about a year. I am using the sensors that come with the unit and have had great luck with them. My only suggestion is to order Felpro gaskets/ o-rings, perhaps the ones included are fine but I really want top of the line. Next one that is leaking will get one of these.

Oil on bottom was most likely melting but also having no solid seal to bottom o-rings was probably not much help.I had smoke coming from heatshield and coolant/oil leaks. So far replacing this has stopped it but I also realize now just how much oil sat in the little crevasse under this cooler. I did put a picture up of the oil approx 2 inches deep, definitely make sure you clean all of it up because it will not go anywhere unless you get to it only so much can evaporate.As you can see the remnants of the gasket on the burnt one on the left. New part was a perfect fit and the screws and gaskets included for reinstallation was of great value and quality. Even the 8 e torx screws (should be five) seemed exact fit and no trouble at all putting back together.I really appreciate this product and thank you to the seller for the great price as well I hope it stays affordable for others and at the time of purchase it was about 75 dollars.