KREGKMA2700 Accu-Cut 48-Inch Guide Track System With KMA2685 Rip-Cut 24-Inch Precision Edge Guide

Reviewing the Crosscut:OMG this is great! I've got a table saw, and its mounted in a 4x8 table, but this is what I've needed for years. So much easier bringing the saw to the work piece vs the workpiece to the saw. Easy to make repeat cuts and the scale markings are spot on. I previously set up my dedicated circular saw for the Accu-Cut XL, which and mounted to the attachment. Bought the cross cut and four foot Accu-cut to add to my collection of tools. Kept the my dedicated saw in the base I already had it installed on, and it worked perfect in the cross-cut. Just switch back and forth with no problem and the scale remains the same. Really happy with setting my cross-cut on a specific measurement and getting the exact cut without picking up a tape to double check myself.

They work very well, they are easy to use and they fit good. I am concerned about the build quality and durability of them over time though, the plastic is the cheaper kind, not the good durable stuff so I hope they hold up for the long run.

Good product, mostly for straight cuts, but not angled cuts. The saw works well for straight cuts, but if you put a 45 degree trim cut it it is not accurate. Setup 1st time is slow and difficult, so have extra wood. If work area has dust, it will cause challenges with the Track Guide and accurate work, but better than free hand. This is not a FESTOOL item, but good for the occasional need if patient.

These 2 items work great for me. HaPpy Camper.I don't have a truck, just a suv. Wanted to build some wall hanging sliding glass book cases.Went to HomeDepot to buy the cabinet making plywood. Had them rip 15" X 8' to transport the wood.I glued the 2 15" together, [back & top] but when I cut the 15"x15 3/4" ends, they didn't line up. What gives?When I cheched the 15" x 8' boards, found out the last 3 and a half feet, the cut was 15 & 1/4". The guy must of picked up the ply wood when sliding through the saw.I was ticked.So I use the 48" Guide Track System and it a amaized me there where no saw marks on the edge at all. Perfect 15" on both boards. Sides lined up prefect.Used the Precision Edge Guide to rip the bottoms. and most of the rest of the pcs. Talk about a straight cut. Just WOW, very Happy with this design.Overall, when your working with 4'X8' pcs of wood these 2 items beat your avg. table saw. esp. if no one there to help with a massive pc of wood.Very happy with the design of both 48-Inch Guide Track System & Rip-Cut 24-Inch Precision Edge Guide.Fits my Dewalt worm drive saw very nice.Great product.

To be honest, I didn't use the 48" track system yet so this review is for the 24" rip cut. I almost gave up on this but I'm so glad I didn't. Watch a few videos on Youtube before your first cuts. I keep a 4X8 sheet of 2" foam insulation in the garage. I place that on the table and then place the plywood on top. The wood will not slide as long as you go slow. The cuts are very clean and consistent. Set up is also key. Spend the time to get your circular saw attached correctly and the rest is just practice. I just made a dozen cabinets in may garage and this made my life much, much easier.

I bought the Accu-cut & Rip-cut together. Assembly with my SKIL saw was easy and so far I've ripped a 10' 2" X 8" into two 2" X 4"s and some 3/4" plywood for side panels on a utility trailer. I will be doing some more plywood cuts today using both the accu-cut and the rip-cut. I found both to be well made, easy to assemble, and easy to use. I would recommend viewing some of the YouTube videos on these products for some very useful additional tips such as cutting plywood on top of a 4' X 8' sheet of foam insulation. I do recommend this product for the occasional home DIYer.

Accu-cut works great, I was surprised at how accurate the cuts were. I was able to do finish cuts in full sheets of ply for cabinet work. The rip cut is just ok. It's fine for rough cuts, but not accurate enough for finish work; too much play in the jig to be precise.

After reading the reviews and trying the fit of the base i found it to have some slop side to side. to remedy this i used a strip of UHMW slick tape approx. 1/8 in. wide on one side of the saw base, Then i used paste wax on the base and the track. Now i have a very accurate and low cost track saw. i wish they would sell x-tra track at a reasonable price and this would be a great long track saw.

Yes for the same price you can pick up a budget table saw but I still think you will get a better cut with these. I have paired them with a Ryobi circular saw as I don’t have a plunge saw and I have had great results.Setting up is easy and it feels wrong that you are cutting the plastic on your first use but I checked and double checked that I was following the instructions carefully.Once set up you don’t need clamps and you can cut straight rips and cross cuts with so little effort. I even used it for making a t track slot which whilst taking a little while was very easy and accurate.The saw can be detached again from the guide if you don’t want to use it, and as it has a feature to remember how your saw goes in you don’t have to set it up each time.The accucut grips the wood with no need for clamps which again I was a little nervous of but it works incredibly well.This has been a game changer for me and in a small work place or in the back garden it’s a very useful bit of kit. Don’t regret not buying one.

I'm relatively new to woodworking and building out my tool collection, and these have been a great add. I was considering a table saw but wasn't sure of what I wanted yet, and thought that these 2 guides would allow me to use my circular saw much more effectively in the meantime. While building a desk and locker for my home gym, I was able to get repeatable, accurate cuts from 3/4" plywood very quickly with minimal measurement or second guessing.The instructions for setting up the track portion with my Ridgid cordless circular saw was pretty easy, and watching YouTube videos helped as well. There are lots of folks using this and was very helpful when making my purchase decision, as you can see it's utility pretty quickly when breaking down large pieces of plywood stock. Compared to following a line by hand and measuring each cut, my productivity and efficiency is greatly improved due to the repeatability and ability to trust that a cut will be straight with minimal effort lining it up each time. So far I've been using the rip cut more than I'd expected, but the accu-cut has been helpful as well. Still may buy a table saw in the near future, but am now in no hurry because I feel I can do pretty much anything I need with this set (and when I build a new shed this spring, I can carry these out to my backyard and spend more time working and less time shuttling around wood and tools.

I planned to buy the kreg rip cut and accu cut for a long time before I finally got it. Its a great tool for breaking down plywood. I don't have access to a lot of tools at my house so adding these to my circular saw helps me do much bigger jobs with a high degree of accuracy.

Le guide de bordure fonctionne fonctionne bien et le guide de longueur avec la bande antidérapante dérape

Product was the same as describe in the description on the web site. Very satisfied with the product.