Mach5ive Screen Saver- Clear Screen Protector for Resin 3D Printers (Phenom/Phenom Noir/Phenom Prime - 3 Pack, Clear)

After nearly ruining the screen on my mars 2 pro with a broken fep I decided to get this for my new Saturn s. It has nice holes that really help line it up properly. Installation was easy. I've seen some reviews saying they scratched it while installing but those people didn't read the directions. I used a plastic scraper to install it and had no issues. The only issue is the static with this thing is intense. You practically need a clean room environment or you are going to have a few little bits of dust under it. So far it hasn't had any effect on my prints. The other unknown is the outside edge is not stuck down because of the tape around the screen. Time will tell if this is a problem. The directions say it's normal but I'll be keeping an eye on that. I print at the edge of the plate pretty frequently

Great product worth the money to protect a far more expensive screen. Take your time installing and the end result will be flawless. You may notice bubbles when you apply the screen at first but as long as your taking your time they are mostly formed on the interface between the secondary firm and the screen protector not the screen and the screen protector.

When I put it on my printer, Phrozen Mighty 8k, there was a long bubbles going around the screen because it covers a good 1" past it for added protection. After some reading and researching I found out it is ok. I am new to 3d printing, so I wasn't sure.It went on really easy. Basically if you can put a screen on your phone you can on the printer.

It is easy to install and takes almost no time, but can save a day as it did for me, when I got small puncture on FEP. Just threw new protector, new FEP and ready to go, saved my screen.

So I got this to protect my Mars 2 Pro. The screen protector doesnt perfectly match the edge of the printer space but this is simply cause they had to make it fit multiple printers so no big deal, just don't try for a 100% match to your printers edges. The gasket on the Printer makes getting a bubbless edge impossible but hopefully it won't effect prints much, and I rry to avoid getting too close to the edge. The squeegee is not ideal. It's a peice of Cardboard with some fabric on one edge, doesn't really work for getting all the bubbles out. I have not tried printing with it yet but we will see how that goes soon

Ok so let me preface that I just got two different 4k printers and so I could be having information overload. But so far I am not all to happy with this product.The Elegoo Saturn S version seemed pretty straight forward to install as it had precut wholes to put over which allowed a quick install.The Phrozen Mighty 4k one however was terrible to install as there was no know where to put it so I had to pull it back and to set it causing a dust particle to find home on the screen. So had to use another and was able to get it on with minimal bubbles at the end.My take at this moment - Mighty 4k needs to have a similar cut otherwise save your money and get any old screen protector - Both versions need a better squeegee to get the bubbles out one is like a credit card which seemed to scratch the protector the other was a piece of cardboard with a thick bit of cloth at one end. Please put a rubber squeegee - Provide better alcohol wipes. the one you gave was such a waste. - Update your installation process as I am pretty sure that I should not be leaving the tape on the printer from the LCD but could be wrong. I just know that the protector went over that which means it will most certainly come up. Note that I didnt look on their website so they may have an updated video, if so well then you should not provide steps and instead just say look online.I will update this as time progresses to show how long it seemed to last and any issues I might have seen just so folks can help save time and error.8-17-22: Installed two different versions. The Elegoo Saturn S and the Phrozen Mighty 4k.

Really has a lot of static electricity but works great and protects your printer from leaks.

I used the help of a plastic scraper to apply it slowly and was left only with bubbles at the edge where the tape dips in otherwise it’s nice to have a protector that overlaps the lcd incase of a fep break much less to worry about. I would highly recommend getting this (I use a mono x 6k)

Dose not fit creality halot one, says on there website it will, IT DOESE NOT

Spent about 30 mins trying to apply the sheet without air bubbles found it to be and impossible task.. I cleaned and prep the surface before hand and didn't help that the card to flatten out the bubbles is 1/3 of the size of the screen. Think tempered glass would be the way to go next time.

when placing this on my mars 2 pro it was needed to be cut about 1 -2 inches on each side.

Very easy to apply and seems great for purpose.

A 30$ screen protector is worth the saving of a 50$ screen and hours of lost print time, plus the shipping wait on a new screen.I forgot to tighten down the vat all the way so the prints weren't peeling off the fep sheet and instead were pushing the print down over and over again. INTO the screen protector. The protector was badly damaged but it did it's job and didn't leave a single scratch on the screen itself. I peeled the old one right off, and didn't have to wait on a new screen protector, Because guess what? It comes in a package of two. Perfect upgrade to any printer. Well worth it!