6LED Car Truck Emergency Beacon Warning Hazard Flash Strobe Light Amber/Amber 4-pack

The media could not be loaded.  Exactly what everyone is looking for. Slim, multi-patterns with memory, heavy duty, easy setup, extremely bright and AFFORDABLE !!!! I just wish I ordered 2 more !!!! lol. I was concerned about the reviews on day time running and I don’t have anything negative to say but i have solid white also so very well could have the better effect. The wires are extremely small but that’s good & bad depending on how you look at it. Nevertheless, if you want something bright, slim & many flash options, This is what your looking for without a doubt.....

A nice light overall. Great as secondary warning lights. Not as bright as I'd like during the day but at night... WOW! Nice! Good visibility off center, too. I wired all these together with a chunk of 18/3 extension cord I had laying around, to a 5amp circuit on my Blazer Wireless switch block. Black (-), Red (+) switched, Yellow (+) momentary switched. The Yellow wire is wired to a 3amp circuit with other multi flash pattern lights. Each light set has a physical momentary switch mounted under the hood. Turn on the 3a circuit and press the momentary switch to change the flash pattern of which ever light set I want to change, then turn off the 3amp circuit.Wiring Tip: Hook up each light individually to a 12v power supply to check the flash pattern, touch the Yellow momentarily to positive, until both sides stay on. Now, once hooked up, all lights will cycle through the same flash patterns.Mounting tip: Only drill the 1/2" center hole. Use that grey, heavy duty, double sided mounting tape to stick it to the mounting surface. Cut a 1/2" hole in the center of the tape. The 1" tape fits perfectly on the back side and makes a nice water tight seal.

The media could not be loaded.  the color they call amber is really not. the orange on my other similar light heads at similar cost (astra depot) are much more amber/deeper orange. These are more of a white/yellow color. the pattern control is with a 12v + which makes it very sensitive and prone to unwanted pattern changes. Other lightheads strobe pattern is controlled by a ground connection. with this light head you can change the pattern by juct tapping the wire w your finger making it difficult to select and keep a pattern during installation.i returned them as soon as i tested them. would not buy nor recommend

The bench test appeared to work well however after a custom hidden installation I found out that these lights do not hold the selected flash pattern.I was using these to come on when the reverse lights came on. It seems that the lights have to initialize when they are turned on but if that initialization is not allowed to complete (say going from park to drive or drive to park) the little power pulse it gets when it goes thru reverse, switches the light to move to the next program. I have been able to reproduce this issue on the bench. I would steer clear of these lights. I have found them very irritating even when they are on a toggle switch.I purchased the white/yellow (amber) whatever you want to call it and found that they were bright and the yellow is, well, yellow is an appropriate color to get bright light though.I will search for a better set of lights and the only consolation these lights are cheap enough to toss instead of return. By the time I "undo" the installation the cost would be excessive to return these lights. It will just have to wait until I get a set that actually work the way they should.

They are very bright and easy to install. Small enough to not get in your way anywhere you decide to place them. If you want it to look professional use a 13/64" or 7/32" drill bit and drill the hole center of where you want to put it for the wire to pass through. Then silicone the hole after wire is pulled through and light is screwed in place to prevent any unwanted moisture from getting behind the light.

The media could not be loaded.  Strong construction. The screws strip easily so be careful not to over tighten. Other than that I am highly satisfied with the value I got for the price. On the bench test they appear very bright. I am waiting on a new switch box for final installation on the vehicle but they look great!UPDATE!!These lights have held up very well. I have 2 mounted inside and 2 on the bumper. I added a little silicone to the backs of the ones mounted outside for some extra weather resistance for a safe measure. Very bright. Only con to these I have found is that I cant get them to sync to each other.

Honestly, I was mildly disappointed by these. They're really a white LED inside of an amber lens, so they don't have quite the same eye-grabbing color of an actual amber LED, and some of their light output is wasted. The flash patterns also didn't include a mode that was a dim solid on, which I was kind of hoping for, but probably isn't a high priority for most users. I wasn't really enthusiastic about the flash patterns, either - very few of them use all the actual LEDs at the same time, but instead switch between half of the LEDs on each unit and the other half. But they do have one or two simple flash patterns that use all the LEDs at the same time.But, they are fairly bright, and they do seem to retain the pattern you set them to.

The delivery time was prompt. When I opened the box, all the nuts and bolts were loose and had worn mark's on the three (not four) strobs. It appeared as if this unit was a return. Someone had (poorly) sliced all three strobe together. Then they cut two of them off of the splice. So two units had very short wires. The third had a longer cord but still contained the slapdash splice. Also half of the loose mounting hardware was missing . There was also a sizable washer that didn't seem to fit anything. All returns should be inspected prior to sending them out again. Poor quality control. I sent it back, woe be the next customer.