VEVORBoat Trailer Dolly, 420lbs Load Capacity, Carbon Steel Trailer Mover with 96''-116'' Adjustable Length, for Moving Kayak Motorboat Fishing Boat (420LBS)

This dolly is well-built (heavy) and designed to meet the need - I agree that there could be a little more weld on the wheels and that the instruction photos are poor but it wasn't really that hard to assemble - I would also reiterate a previous comment - the extra bolts, nuts, washers are in one of the tubes - even has a sticker on it to tell you, so check there before posting that it is missing.It is not as portable as those smaller dollies but I was not enjoying having to lift my heavy kayak and drop it on the C-Tug and then cinch it down - plus the C-Tug wheel dont roll as well as the Vevor does although I do wish the wheels had bearings - it looks like they just ride on the plastic(?) material.The breakdown of the dolly is pretty easy - I just bought some of those wire lock pins and used them everywhere - makes it a snap to assemble/disassemble.I am considering a mod to it to accept a coupler but will use it as-is for a bit to get a feel for if needed or not - I also may enlarge the pad holes to allow for maneuvering the pads to a greater angle - we'll see on that one too.Edit - Used it for first time on 10/5 - worked well easy to put into water than to get out - the wheels float so you have to step on the trailer to drop it for loading. The handle is bad - not a good pull point - I will look at mod to make it more comfortable. I can tell you that if you have a steep ramp and a heavy kayak that it will still feel heavy - thinking about modding it to put a trailer coupler on it to pull w truck up to an unloading spot. Otherwise - it is easy to assemble/disassemble, faster to get into/out of the boat ramp area, and I didn’t get water into my boots like I used to so all-in-all it is a winner for me.Edit #2 - Was having issues keeping the kayak centered on the pedestals when loading it from ramp - would take forever to get it right as you also still have to deal with the floating issue so, I added a doubled up 3” strap that spans the pedestals (similar to the dynamic dolly that Greg Blanchard uses) - problem solved.Edit #3 - Hobie Outback still twists between the posts even with the strap - looking to mod the posts (grind them down on an edge) to allow the base plates to be more on an angle. Will update with results.

Bought for a 12’ Jon boat for family pond.Kind of steep where we launch, but this thing works great, getting the boat in (only one required) and out (takes two). But so much easier than carrying the boat. Can launch with everything in it.

A game changer to launch my inflatable. Although a few upgrades and changes were are required to get the most out of it.1. Ditch the wheels/tires. It comes equipped with cheap plastic roller bearings and bushings. They won't last long. The wheels have a non-standard bore size so good luck finding replacement ball bearings.Look for 16" flat free wheelbarrow/garden trailer wheels.The axle on the trailer is also metric so for the new wheels you'll need 20x35x11mm bearings.2. I added a trailer coupler to tow my boat from the campsite to the ramp.3. The support stands with the rubber pads didn't really work for my boat. I removed the rear ones and used PVC and and an aluminum square tube to support the rear of the boat.4. The photo in the description is misleading. The overall trailer length is adjustable with the "rod", not location of the front pads.5. The instructions are terrible, but it's easy enough to figure out.I ended up spending more than the original price of the trailer to customize it for my needs, but it was still 1/4 of the cost of a Dynamic Dolly.

It needs a pin hitch adaptor to hook to my garden tractor. A simple 3/8 inch slot with a 3/8 pin hole would do it. It may be difficult to use with small boats by reason of the front support location, which cannot be changed. Otherwise a rugged and simple trailer. Get a color print of the trailer because the assembly instructions are rather worthless.

There is a reason that this boat dolly gets returned so many times (according to Amazon). I received mine in a beat up box. It had obviously been returned. Parts were incomplete as others have noted. Not just screws and bolts but also missing plates. The kicker is that they included the incorrect user manual and assembly instructions. The product I bought is the CY420. That is also what it said on the box, but the user manual is for model QYC1000 as noted in the photograph. I needed the trailer, so I improvised with parts that I had in my garage, truly a Frankenstein trailer. I do not recommend this product for anybody else who is looking for quality boat dolly/trailer. Oh, and they don’t have a toll-free phone help desk….just an email address. Vevor motto is “Tough Tools, Half Price”….more like “Half #*@“

we love are kayak trailer, we pull it with our golf cart , we put a trailer hitch on the trailer and the cart so when we hook them up, put your toys on top 2 kayaks or canoe with tubes and floats and then pile everyone on the golf cart and then just grab your best cocktail and head to river or beach. you could do this with any trailer, BUT, with this handy trailer we can take it apart in the middle and the two parts with the wheels still on fit in the same trailer that the golf cart goes in and we go back home.

Holes misaligned on one part and not completed on another part. Had to drill them out which can’t help stability. Assembly instructions could be improved by including some drawings.

Where I do agree with others that the assembly instructions are lacking, it’s pretty easy to figure out.This thing was WAY more sturdy than I was expecting and boy does it make moving out boat easy!! I’m sure pulling it behind your golf cart is not approved for general use… but that also worked amazing!!I would totally recommend this boat dolly.For reference our boat is 100 Lb and 8 ft long.