SUNLUHigh Speed PLA Filament 1.75mm, 30mm/s - 600mm/s Print Range, High Flow Speedy 3D Printer PLA Filament, Designed for Fast Printing, Neatly Wound, 1 kg Spool, 2 Packs, Black+White

It is not as white as advertised but meets the quality output. Print quality: I would have rated it higher, but it was more gray than white. I really needed to be white like their other filaments. Would I purchase this again? Yes, as long as it is at the current price and for a project that needs a gray undertone.

Just started using this filament with a new 3D printer. So far, it's been working out well. There is good adhesion, and produces excellent prints. While I've only used it for just over a week, I'm very pleased with the results.

No problem printing the black on a p1s stock pla settings. The white has been problematic. It strings like crazy. I've tried adjusting temps and speed but no luck. I've even dried it for over 12 hours. Not sure if it the color or I got a bad roll. No problems with the white pla+ even at 220c and 300mms.

I received this as a sample pack so I could try out a different vendor from my normal PLA filament. The larger pack is not resealable, nor are the individual filament bags. The individual bags have a hole in them (see last photo), so be sure to store them in a box if you have high humidity. I am using a stock CR-10 V2 as my printer. I messed up the g-code on the first tower run, but as you can see, there was some stringing at 225 on both the cancelled print and the full tower. There was also some stringing at 180. Otherwise, the rest of the tower looks really good. 190- 210 range are all clean, no ghosting of the numbers, no stringing, etc. Sliced in Cura with bed temperature at 50, and nozzle temperature change every 5mm. Feed rate was 35mm/s on initial layer and 70mm/s throughout the rest of the print. I also started to print an SD card holder (seen in the first photo). Bed temp 60, nozzle temp 205. No issues in the initial layers of that print. Skirts used for all prints. I will definitely look to Sunlu for filament on the future.

Fine color assortment- with the cost of a full 1kg spool at ~$20, so little feels skimpy- Amazing basics assortment is much more satisfying with regard to price and amount.

I usually like Sunlu pla but the High Speed Sunlu is horrible. Its very brittle and does not print well.I usually use Elegoo Rapid or Creality Hyper and never have issues. I figured I’d try this and have wasted over 2 rolls trying to get this to work.Stay away from Sunlu High Speed!

Breaks sitting overnight in k1 printer. 15% humidity in room and even tried filament dryer still broke after a day just sitting in the tubes. Do not buy get something else I'm out almost $100 for this crap because I decided to buy 4 twin packs of this junk while they had a coupon for it

I process a lot of 3D printing orders for my small business, and I always need to have a good spool of black PLA on-hand for it. This stuff is sturdy, prints smoothly, and works quite well, especially at higher speeds. (Do take care to use the lower temperature specified on the spool [180-190°C], especially at traditional print speeds.) It has a beautiful sheen to it that is hard to replicate with most other black filaments.My main complaint is that, when performing color changes, I couldn't get the second color to stick very easily to this PLA. I had to manually lower my Z-height and bump up the temperature by 20°C in order to get a bond. It's also difficult to keep it from dribbling and leaving "zits" on your prints, which is another reason why a lower print temperature is so important for this stuff.All in all, it's not without its problems, but it gets the job done, especially for functional prints.

かなり丈夫な感じがします。強度の必要な物を作るのには適していると思います。ただ仕上がりはあまりキレイな感じがしません。

Liked - plastic spool fits in AMS. Prints fine on x1c with generic pla settings - I tried faffing with the settings but gave up and went back to it prints fine anyway.Don’t like - colour - it’s a really bluey /dirty white - I know it’s a odd comment to make but compared to a print of my standard BL white - for this reason I wouldn’t buy again but would buy other colours - this was only a test and easy to use before printing Halloween tat.No issues with tangle or roll packaging /humidity in transitit’s a big big difference. Photo shows this colour in right - banbu stock white on left

Prese per provare i colori, molto belli...

Ich habe vor Kurzem das SUNLU Hohe Geschwindigkeit PLA Filament 1.75mm ausprobiert und bin wirklich beeindruckt. Die Qualität dieses Filaments ist ausgezeichnet. Die Druckergebnisse waren konsistent und von hoher Präzision. Ich war angenehm überrascht von der Geschwindigkeit, mit der meine 3D-Druckprojekte abgeschlossen wurden, ohne Kompromisse bei der Qualität. Dieses Filament hat sich als äußerst zuverlässig und kompatibel mit meinen beiden Druckern erwiesen. Als Bonus ist es umweltfreundlich und zu einem fairen Preis erhältlich. Ich kann das SUNLU Hohe Geschwindigkeit PLA Filament 1.75mm jedem 3D-Druck-Enthusiasten wärmstens empfehlen. Es hat meine Erwartungen übertroffen und wird definitiv ein fester Bestandteil meiner zukünftigen Projekte sein.

Das Filament ist in Weiss und die Rolle ist echt gut ! ich Drucke auf meinen ENDER 3V3 Se neues Modell mit 210 Grad und er druckt super ! Hab sogar die Geschwindigkeit auf 180 mm getestet Highspeed Druck und es rennt 1a ! Die Farbe ist aber eher Grau Weiss bei mir anstatt Weiss ! Aber ist Cool ! Gefällt mir ! Super Top !