Frylr Baltic Birch Plywood Sheets Box of 45-12 x 12 x 1/8”, 3mm Thickness Perfect for Wood Burning, Laser Engraving Cutting, Scroll Saw Nature Veneer Color, Stronger Than Basswood, A/A Grade

If you take pride in your work, then you really need to purchase from this supplier. I purchased 90 pieces of birchwood and will be buying a lot more. All my cuts have been clean and are very detailed. I have not had a single project not cut clean, 100 percent. No more failures to completely burn through. No more using a razor knife to finish a cutout. The finish on the wood is outstanding and not a single warped piece. No need to sand the wood before processing. I am even able to cut at a faster speed without any problems. NOTE: Due to the serious packaging, you will need a few extra minutes to unpack it.

A few minor hairline scratches from machining. Wish they sold it in 36 x 36 or 36 x 24 size!

I recently had the opportunity to review the Baltic Birch Plywood set, which came in a pack of two pieces. I must say, the price for the 45-pack is astounding, especially for birch plywood. Once you dial in the settings correctly, the cut is phenomenal— I personally found success with a 100/6/2 cut. However, it did take some trial and error to get there. Overall, I'm pleased with the value these plywood sheets offer. One thing to note is that you may encounter some issues with the glue, which can cause a bit of charring. Nevertheless, considering the price, these plywood sheets are a great choice for various woodworking projects.

Second time purchasing this product. Have an ELEGOO Phecda purchased on kick starter. The wood is great for laser. I've used some birch plywood for making tags for gardening, but the resin sometimes causes the cuts to not penetrate fully, very inconsistent. However, this product is great. It's not a resin, but more of a standard glue. Although the glue does breakdown for plants tags because it appears to be water soluble. However, on other projects, it's fantastic. Great for cutouts, engraving, diorama's, etc.Out of 50 projects, some very complex, I've only had 1 maybe 2 times that I didn't get full penetration in a certain part of the boards, but every other cut location worked as intended.It is 3mm, not 1/8", so I had a few box projects that didn't mesh well because I forgot to account for the actual thickness. That's on me, not the supplier.The boards are not 100% flat, but some have a minor amount of warpage. Hasn't been an issue so far, just to note that about 30% of the wood panels do not sit 100% flat on the laser cut bed.NOTE: offset is usually fairly minor, maybe 1/16" of an inch from corner to corner on some panels, but have not had any failures in laser cutting because of this.

I continue to purchase this produce because I can depend on the quality in my laser business. OUt of the 45 pieces two or three will have back sides that have minor defects which can be cut around or hidden with paint. The sheets are well packed and remain flat after opening. I wish they would offer the same quality in 1/16-inch thickness.

I use these for scroll saw projects and they hold up well. I've found no voids between layers and no warpage.

I found 8 of the 45 have filled knots in them. A/A wood is not supposed to have any fills or knots in them. Both faces are supposed to be pristine. If it was rated as B/BB then one face can have blemishes. Also I have several that when engraved there are holes where it went through the 1st layer (Veneer) and there was nothing underneath it. I have worked around the knots but the bad engravings are just trash which is wasted wood that I paid for. Not a happy camper. I'll not be buying from this supplier again. If I hadn't had a deadline to meet so urgently I would have returned it all. I gave it one star in the value part because even though it was a little less than other suppliers its value went down since I have thrown several pieces away.

First of all, the 8 pack’s main image shows it being a 16 pack - blatant deception. Of the 8 boards I received, 1 look good enough to use the full sheet for production. The other 7 had obvious seams, completely different veneer colors, gaps between seams, and spots/scratches that didn’t blend with the walnut color. Strips of the veneer almost had a blue tinted foggy appearance. Using a majority of any sheet for a project looked tacky and I could never give it to customer looking that way!I will say that they were consistently 3-3.1mm thick and were nice to engrave/cut on my 10w diode laser. I had to use most of the boards for smaller projects that fit within a single strip of the veneer due to how horrible the strips lined up on the sheet surface. I used a bit of danish oil on the light colored scratches/grains and it blended well, but I shouldn’t have had to do any patchwork or small projects with “grade A” plywood. Very disappointed in the overall cleanliness of the overall sheets as it was pleasant to work with and look great with polyurethane finish (when the veneer colors matched up).Maybe I got a bad batch, but not worth buying again since I had to work around the flaws to produce a quality looking finished product.

Don't buy this product if you want close to the right dimension. Advertsied as 1/8 or 3mm. They measure .105 and 2.6mm. Thats a big difference when you are designbing for 3mm.