WOWLEDPC Gaming RGB LED Strip Magnetic for Desktop Computer Case Lighting Compatible with Asus Aura Sync | Gigabyte RGB Fusion | MSI Mystic Light and Motherboard with 4pin 12V RGB Header, 2pcs 30cm

The media could not be loaded.  These are really good if your motherboard has RGB headers and good software. I'm using the Asus X470 Prime Pro and it works perfectly with it. It actually comes with a 3 to 1 lead so you only need to use one of your headers, and one of the leads is extra long...allowing great flexibility in placement. My case is steel and as they are magnetic, it really helps to place them. There is a peel off sticky backing for sticking to non magnetic surfaces.Totally recommend this product.Edit: Just an update, these have been in the system over 10 months now and I still think they are great, no problems, work well, easy install and I would buy another set in a heartbeat if I needed more. Was surprised to see a few 1 star reviews because they are a great product. I am a genuine buyer, not a shill because how many shills come back and update their review.P.S. Oh I went NVIDIA RTX 2070 in the end, tried to go AMD for the GFX card, but it never worked out...2 DOA cards

The lights are fine. Good brightness (not blinding, but sufficient). They stick well. My mobo has an issue where you can set the pulse/ colour/ style/ etc in the bios, but the desktop software freezes when you start it. That's not the led's fault, so no criticism there. I mention it because you may have the same issue and wonder what's going on.Anyway, once they're up and running, they're good. i've got them cycling through colours, and it's nice and calming.If you're putting them in a PC, I would recommend that your PC case has a window in the side. In almost all cases (save x-ray vision or those with photophobia) this will dramatically improve your enjoyment of the lights.

On the plus side, the strips were easy to install, the magnets strong enough to grip the case well. However, the connectors are quite loose, i've had to use tape to hold them together properly. The colour representation is not great, outwith the three primary colours that is. I find the yellow is more of a green and the white is more of a very pale blue. I think this may be fairly common with RGB strips rather than the more expensive RGBW ones. However, in particular if you're sticking with primary colours (like I am) then they're absolutely fine for the price. you do get what you pay for though. Don't get me wrong, they're not terrible, just not great either......

These LED strips were easy to install and came with a three way splitter so they could be run from a single RGB 4-pin plug. A single 4-pin extension cable was included, too. Good brightness of strips and the range of colours they can display is what you'd expect from RGB. The magnets within the strips could do with being a little stronger, though they are sufficient to support the weight of the strips - just be careful with your cabling and don't let the weight of that pull the strip off!

The first time i bought these 3 years ago, they were awesome. But i have purchased them again twice this year and returned both units as defective. They do not display the correct colours, so the original strip correctly displays the selected colour, but the newer units are always not the selected colour. Other customers also had the same issue, so it seems they don't care enough to fix this issue.

The product works well. The magnetic adhesion is strong enough that even when moving my case about they haven't moved at all, but the leads just aren't long enough to do much with absent an extension. Can be easily controlled through the motherboard's RGB software. One strip is the main source of light for my entire interior and lights up the lot nicely.I installed on an NZXT H500 rig (I'd share photos but Amazon won't let me for some reason), and the first thing I wanted to do was place a strip along the nearside top of the case so it lit the whole interior but stayed out of sight. Obviously I wanted to run the cable around the back of the case so it was out of sight too, but it's so short that when it's plugged into the bottom of the motherboard, the strip itself is pulled toward the back of the case as well.I only have the basic 120mm fan installed on the top intake so it shouldn't be that much of a stretch, but it is, and the strip ended up twisting around it and instead of shining down, shone up through the grating. And of course because it had been pulled back so far, the strip itself wouldn't reach the right hand side of the case anymore, only stretching about 2/3rds of the way across.Even like this, it did a good job of lighting up the whole interior, but it was very annoying, so I bought a 20cm extension lead and now it sits flush along the front edge as it should, but that meant instead of £12, this cost me £16 in total.With the second strip, again due to the short lead, there's not much you can do with it and keep things out of sight, so I put it vertically down the inside of the support bar, and it gives a nice even glow.Basically, this is an easy kit to set up and the strips are fine, but without an extension lead or two, your installation options are limited.

The media could not be loaded.  As others have said!The connections are floating, and need to be secure.You can easily achieve this by plenty of cable ties and good routing.I fit this kit to my set up, also ordered some extension cables from Amazon.They were essential.A couple of hours later, I had a display that I am proud of.I have no problem with this set at all.... It is a 5 out of 5.Just make sure that you know what you need to do, and prepare first.Reviews are very helpful in this way.I say get them...

Looks great and easy to plug in. Takes the 4 pin rgb header, but my adhesive keeps falling off and the light drops into the case. Needs some improvement, the magnet is very weak and won’t hold it.

Finnicky set-up depending on case model. Good light levels and very responsive.Good deal if you don't want a flashy setup.

These LED strips have really improved the lighting inside my case by far. They sync perfectly with MSI Mystic Light Sync software and I had no problems at all installing them. What was extremely nice about these is that they have magnetic strips in them so if your case is steel then they should stick right to your case without using the sticky adhesive strips they also come with. I definitely recommend these to anyone trying to spice up there computer. Also these are the 12V RGB not the Addressable 5V RGB so make sure you figure out what headers your motherboard has before buying these.Hope this review was helpful.

Das Produkt hat ein gutes Preis/Leistungs-Verhältnis.Vor dem Kauf sollte man sichergehen das man ein Mainboard mit 4Pin 12v GBR Anschluss hat.Ansonsten Brauch man einen Converter/Controller zum anstecken der Led.+ Produkt kam gut und einzeln verpackt an.Alles hat beim ersten Versuch geklappt.Die LED Streifen sind von sich aus sehr Hell und dementsprechend für jedes Case geeignet.Magnet hält prima und verrutscht kaum bei Berührung.- Das Produkt hat mehr auf die Led gesetzt als auf das Zubehör. Das gelieferte splitterkabel ist für manche Anwendungen doch etwas kurz und die Kontakte sind nicht fest so das sie auch mal auseinander gehen können (natürlich nur bei der Montage).Wer eine günstige Variante sucht hat hier eine gefunden wenn er Bock auf fummelarbeit bei dem doch etwas kürzerem Splitter hat

Iniziamo col dire che nella confezione troverete 3 striscie RGB separate, che potrete connettere insieme tramite il cavetto a 3 connettori (4PIN) +1 (quello che va connesso alla MB). Presente anche una prolunga di circa 20cm. per far raggiungere una zona del case del PC un po' più lontana, rispetto al connettore della MB, ad una delle strip.Quindi nessun problema per fare "3 lati" all'interno di un case.Ora, la cosa FONDAMENTALE: trattasi di strisce LED a 12Volt/4Pin, quindi non compatibile con le MB con connettori integrati per LED 5V/3 PIN. 100% compatibile Asus AURA. Ottimo. Consegna Amazon impeccabile, come sempre.