Repairwares Washing Machine Drive Belt WH01X10302 WH01X10353 1264395 175D5131P001 175D5131P003 AH1482278 AP3968432 EA1482278 PS1482278

This belt appeared to be way too small. However, it worked perfectly. Watch some YouTube videos on instalation.

Product fits really tight be ready to put a little elbow grease on it, but seriously they have a tool I used a blow dryer to help me stretch the belt .

Easy to use, value for money as purchasing a new washing machine is a lot more expensive!! Have had it on the machine for 6 - 7 weeks and still running great!!!

GE specified wrong length for remanufacture. Even their replacement is not right length. GE is aware of problem and mid December 2023 is earliest date they think it will be in stock. P/NWH01X10302

Works on my older GE washer, but I needed to purchase the overpriced belt removal tool (sold separatly) to change out the belt.

I ordered this belt.a year ago in 2021 and it fit well, a little tough to install but manageable with a zip ties and a clamp. I tried to order the same belt in October 2023 and the belt.is at least 1 1/2 inches too small. As others noted, the new belt would not even fit around thw drum alone let alone fit the drum and pulley system. It has different part number stamped on the belt than the original . I will return and I bought a 40 inch belt which fit snugly and works properly unlike this product.

This belt did fit our washing machine, and I think the people comparing the size to the one that was already on their machine are forgetting the amount of stretching these things endure. And for those saying it doesn't fit, I think (unless they bought the wrong product) they didn't put enough elbow grease behind it. It took two grown men to get this belt on our washer but it DOES fit and has been working perfectly ever since we replaced it two months ago!

Okay just installed this today 3/21/24 (3) stars from me seller read below.So just some pointers for y'all.1. belt is small heating it up helps. Oven @ 200 for 5-7 minutes (cookie sheet with parchment paper) makes the belt go on easier.2. use more than one zip tie in one spot. the YouTube video out there uses one zip tie but they have the install tool as well.what I did after heating the belt was put one zip-tie on the right side of the flywheel (the big one in the back) while keeping the belt up on the motor shaft. I spun the flywheel about 3-4 inches counterclockwise and put another zip-tie. then I spun it another 3-4 inches counterclockwise and put a third zip-tie.3. it takes a bit of muscle to get the belt to go on while spinning the flywheel. I kept one hand on the belt at the motor shaft so it would not slip off there. One hand on the belt @ flywheel as I spun it to me, and I used my head to keep from pulling the whole drum assembly out as it is just floating on some plastic pieces and will break.4. if you have 30$ buy the install tool that goes on the motor shaft. you will use this probably once your entire life. maybe twice.5. line the grooves up on the shaft by spinning the flywheel slowly so the belt rides in the correct place.6. when successful (you will probably use many expletives and it will take more then one try unless you have Vegas luck) button up washer, test washer, then have beverage of your choice.wear thin but cut resistant gloves the edges of the flywheel are sharp very sharp.......and the metal obstacles with any piece of household hardware are also sharp...Don't forget to take off the zip-ties. a small note is I noticed the belt will slip under the flywheel even where the zip-ties are or fold around the bottom lip of the flywheel. you will think you have this thing on and boom you turn the flywheel and it pops off. take your time you can manipulate the position of the belt by aligning the belt grooves and motor shaft grooves and pushing the belt up, as you turn the flywheel. go slow use many expletives and savor your beverage afterwards.For the seller if you even read this. might want to look into making these belts out of a more forgiving material where you don't have to heat it and such. include the tool with the belt, if the material isn't changeable. If I had warning the tool would have made my life easier, I could have printed the tool for less than a dollar and the o-ring that holds it on the shaft is $0.18. This is a tool you will literally use one time in your lifetime and would not be expensive to make. instead of 12$ charge 15$ with tool your customers will come back for other parts you carry. Had the belt been the OEM size your review would have been 4 stars, with tool 5.