4PCS Aukur Logo Projector Car Door LED Lighting Entry Projector for Nissan

So, I began my adventure into installing the lights. Some say it clips right in others say it's upside down, etc. These are tips from what I learned when putting them on my 2019 Nissan. Also, if you have not attempted to install yet the tips will seem like garble. So, if you are having trouble getting it to work then come back and read this by then you'll know what I'm talking about. Note: There are two pairs of tiny holes in the plug, don't plug it into the wrong one. Your prongs may be higher than the plugs to cause this to happen. You may need to gently push down the prongs in order to get them to line up correctly. Use a blade screwdriver and gently push. The black round casing for the light may be upside down. You don't know until you plug it in, so to check on this you can take the black round casing out of the clear plastic holder, remembering how it will go back, together, and plug it in without the clear plastic holder. If it is upside down, gently slide the black round casing clock or counter clock wise to line it up the right way. You will notice a small notch on the black round casing. Remember you have to do all that while being aware the clear plastic holder will be in the right and not upside down . After that you want to put the black casing back into the clear plastic holder, where it was. This may be difficult as it won't go into the hole. Just turn it until it drops into the hole. Don't try to push the prongs in first-- you will need to get the round casing into the hole first and then turn the casing to get the prongs back into its position into the clear plastic holder. Finally plug in the light but make sure your clear plastic holder is positioned right and not upside down. That also will determine whether the plug from your car will go on the right side or the left side of the clear plastic holder. Click it in, as now the prongs should slide right in to the right two holes and it should light up. If not you may need to close your door and open it again. I did with my car. I thought it still had it wrong, but closed my door and opened it and it lit up. So all in all for some this is an easy one minute install. For others, you have to realign the prongs, and or turn the casing 180 degrees. So, 30 minutes of trial and error and then 30 minutes of figuring it out but It worked. I'm really happy with them. Hopefully, this company takes time to write up troubleshooting tips on their product.

I have a 2014 Nissan Altima and those that know you see Altima everywhere. So I'm trying to change it up and make it different and unique in my own way. You have to make sure you pay attention when you put these in. The connections have to be pushed down just a little bit so that it can fit into the plug make sure that the connections do not go into the top two holes they have to go into the bottom two holes of the plug. you can also adjust me image by taking it out and turning it if you put it in and it looks like it's upside down.

The media could not be loaded.  Coolness

The media could not be loaded.  This product was super easy to install and it looks really nice on my Maxima. My only 2 complaints was that the product does seem cheaply made and it was not the cleanest fit, but it was close enough. Over all, I am pleased with the end result.

The description on the vehicles says that my vehicles is compatible. I guess I could have looked myself in regards to physically looking at my vehicle but if it says that my vehicles is compatible then I trust that. Guess I was wrong because as you can see in the picture, I have no door lights. Why would you post something that is not right??? That is just bad business. Now I will have to waste my time by sending it back for a refund!

This was purchased for a 2004 Nissan Armada. The package and the product came delivered in perfect condition and was prompt. I do not trust the product structurally. The lens (with the Nissan logo) was not a permanent piece. You could remove this with no effort (would easily fall out). The LED module was also only sitting in the door lens and was too big to properly be placed in the door. If I took out the module, the door lens fit just as an original would; however, you would need to trim some of the plastic (Dremel tool, file, etc.) to get this to fit. I would normally do something like this with no second thought. But, with the loose LED module and lens, I would expect them to fall into the door at the first bump in the road. I am returning this novelty item and will not be purchasing another.

I have a 2014 Titan, and since I had to replace my door lights, I thought I use these. I had to flip the logo, because it was upside down, not a big deal, but as you can see in the photos, the light cover does not fit right. It’s like the back of the light is so thick, it pushes it out. I tried several ways to shove it in place, but it would not go in. I took off the light and put on the light cover to make sure that fits....and yes it does. But as soon as I put the light back on, it would not go in right. I don’t know if I am doing something wrong, or I saw another Titan review and wonder if it just doesn’t fit the Titan right.

These are great! Unbeknownst to me my ‘17 Maxima does not have door lights on the rear doors so I only needed two of them. I have two spares now should one stop working. Really nice looking once installed. I did have to rotate the housing 180 degrees for the logos to read correctly to the person entering the vehicle. I also had to shave some of the plastic door molding in order for them to fit flushly like the factory ones but the plastic is thin and soft down there and it will never show if you decide to go back to the original lights so I really didn’t mind doing it. A great, Inexpensive upgrade to your Nissan.