Bull Ring Gunmetal Finish Flush Fit Retractable Truck Bed Tie Downs for 2009+ Dodge RAM 1500, 2500 (Rear Only) Dually RAM 3500 (Front & Rear) Rail Cap Trim Required to Install (1 Pair)

Great product so far. Took a lot longer to install than what the video shows. On my 2021 Ram 1500, I had to cut out a larger portion of the stake flag cover than they show in the video. Just be ready to cut out the entire Stake Flag Cover all the way around. Once installed, it looked nice though! Haven't had to tie anything down yet, but it looks nice and appears to be fully functioning.

I installed these on my 2020 Ram Limited. The router bits work good. Due to the sheet metal of the truck on one of the front holes I had to cut it closer than the bit would allow to get the hook to fit in. I don't know if this is all truck models, or just the Ram, but there is a gap between the plastic bed piece and the actual sheet metal of the bed. If you tighten down the hooks it bows pretty bad. To keep it from bowing down you need to keep the screws really loose. To fix the problem I used 1/4 MDF around the hole to give it structure. This worked really well. I was able to tighten the screws and now bowing of the plastic or the hooks. Unfortunately it was a trial and error and took some time. You could use anything, but make sure it's around a 1/4 inch.All in all its a good product and better than the hidden style I had on my last truck. They seem really strong and they look good. Spend the money on the router bits. It will save you a lot of time.

Like other's have pointed out, this generally fits but requires more than the video shows. I installed a set of 5066 rings in the rear stake pockets. I didn't feel like buying router bits so I just used the cutting wheel on my Dremmel. I cut the skirt inside the pocket per the video. It doesn't have to look perfect because nobody will ever see it. However, the Bull Ring would not fit perfectly in the hole. I had to then use my Dremmel and enlarge the stake hole on two sides. Again, nobody will see this so I didn't mind. As you can see from my picture, it looks great once installed.

This produce seems to be great. I installed it on a new 2021 Ram 1500 (new body style) with a 6.5 bed. I cannot remember if this was the front or rear set but both fit and worked great the first time I used them. The only reason it got a 4 star for ease of install is bathe front passenger side was really tricky to get installed. There was very little clearance to get it to sit right but it will fit. All the other ones were really easy once the bed rail plastic/protector was trimmed. The actual installation of the all 4 rings took 30 minutes. The setup and clean up was more work then the installed.

When I say solid I mean solid!! These should not have "Bull" as part of the name, the ones you can grab from the hardware store that use a toggle bolt are bull!@$% Amazon garage says these dont fit my truck but they absolutely do...very strong fit in fact they are so strong the rear panel flexes slightly as you tighten your ratchet strap.....nice upgrade, I have them upfront on the rails near the cab as well. I used a Dremel to cut the inserts and I added wooden shims around the opening to keep the bed liner plastic from bowing in as you tighten the Bullrings.

Looks great and works great. It took about 45 minutes to installed. Take your times and be careful not to cut into your trucks. Dremel is what I used. Put a thin razor blade between plastic and the truck rail so if you accidentally cut too deep. It won’t cut into your truck. See pics. Fits perfectly in 2021 ram 2500.

Looks good once installed. Strong and sturdy if done this way. Don't just cut out the square. Use Dremel and tourch to smooth out after. Take the metal plate off and flip over to trace the area to be removed. Take your time. You can always remove more.

Using the router is not as easy as shown on the install video. The first cut I had to go deeper to make the correct cut. The second rear hole (leaving the bit at the same height as the first) the blade cut into the bed rail and destroyed the blade. It was not easy getting the remainder of what needed to be cut away out with various mand tools.Once installed they looked great.

These are great, extremely handy and easy to install. I installed these on my 2020 Ram 1500 and they looks awesome.

Nice product, worked perfectly on the front and rear of my 2010 ram 3500

Installed as explained no issues.