Inner Bed Tie Down Anchors Retractable Truck Bed D Ring Compatible with 2007+ Silverado & Sierra 1500 2500 3500/2015+ Colorado & Canyon - 3000LBS Capacity Only Fit SideWall of 4

Product works great. Installation took a few minutes to figure out but once I figured it out, installation took less than five minutes per tie down. Great product, and well hid when not in use.

These are pretty cool tie downs. easy to install if you read the directions.

The media could not be loaded. This is a really highly engineered and solid all metal product. It does what it should without inconvenience or rattling. My way of installing in a Silverado is a breeze—back the screw way out but don’t remove it, extend the ring all the way, holding the ring slip the upper edge of the backing plate behind the bed wall, LIFT vertically the bottom edge of the plate can clear the wall and slip in, center it up, screw or down. It might take 5 minutes on the first one or two to work out the fiddliness (and to learn to be Gentle so the ring doesn’t snap closed), but after that it is about a 2 minute job.The one in the video has been subject to about 17 loads of compost, wood chips, and dirt. As you can see it wasn’t bothered by the grit and still works like a charm.

The fourth one of these may be easy to install, but it takes 3 to get the hang of it. At first it will seem they don't fit. They do, but you need to remove the screw entirely, pull the anchors all the way out then push them against the black plate so the metal has room to move. Push the big metal slab all the way in and up before trying to push in the bottom of the steel plate. Then life the whole unit to center the screw hole, get the screw started, and screw it in without letting the whole assembly slide out of alignment with the hole.Once it's in the quality is there, with all the load bearing parts made of steel. Probably helps to do it on a warm day, or in a garage with good light and something to kneel on in the truck bed.

There are cheaper tie downs, but why would I want one that I have to replace when I could buy the best for a little more? These inside the bed wall pull out when you need them and snap back when you don’t need them anymore. These babies were not designed they were engineered, tested and then put up for sale! You will not believe how well they fit! Not made of plastic, all metal! They will still be working when you give your favorite truck to your son or if your lucky your daughter! I put them in myself, it really speeds things up if you have a helper to hold the tie down loop in the extended position if not a small vice grip clamped on one side will do the same thing. Some people could probably install them by just backing the screw out almost all the way, I could not. There’s a plate that has to be inside the wall to hold it in place I could not accomplish that with out removing the screw. It might work with a longer screw, but I figured they already tried it out and for some reason it didn’t work.The more you put in the faster you get! Okay I only ordered 6 to start with then I realized three across the front is better especially if using a tarp to keep the wind from getting under it. Order 9 so you have enough for three all the way around. They sell nine for $99. But I got 8 for $99 because they didn’t sell three, only 2 or 4! Since they sell 9, 6, 4 or 2 you have to settle for one too many or one not enough if you do not order 9 to start with. Next time I will return the six and then order nine! I begged to order just one more they suggested that two more would give me a spare. Right away I thought they didn’t have as much faith in their products as I had!

I recently added more of the rice downs to my Colorado as they work well and snap back into the bed wall. The original set still works and look good.

Didn’t fit 2023 Chevy Silverado RST even though they claimed they did. Stars are for the quality, slim look, durability, and function

2024 silverado 2500hd with line-x spray in bed liner.Super easy install, 20 minute total install time (even though I installed one upside down initially and had to take it out and reinstall). Lock the anchor into the open position, remove the screw completely, slide the main body into the pocket, then slide the backing plate into the pocket, holding the anchor in the open position slide plastic face against the sheet metal and reinstall the screw. Prior to tightening the screw completely, test the anchor for functionality. If it is operating correctly, tighten the screw and you are done! That's it!They seem to function smooth. They do NOT sit as flush as the "BULL RING" anchors, but the bull rings have more plastic components that breaks down over time.I have not put these under load yet, but they feel like good quality. These anchor points will be used as secondary security for my load, I don't trust the sheet metal to hold any excessive amount of load.5 stars! Very satisfied at this point!