SuperStroke Cross Comfort Golf Club Grip | Soft & Tacky Polyurethane That Boosts Traction | X-Style Surface & Non-Slip | Swing Faster & Square The Clubface More Naturally

Bottom Line: A key to install is coating the inside of the grip by plugging small hole end with a finger, add solvent, plug larger opening with other hand finger and swish back and forth while rotating the grip. Then empty solvent out the small hole into the grip over a paint tray.Details:The grips are great. Being soft grips, they will wear out quicker than Golf Pride, but I much prefer this feel. It’s similar to Dri-Tac.These are definitely harder to install. My struggles and then success:Attempt 1:First attempt was without a vise, as I have always done. I coated the tape in the shaft with solvent and then coated the inside of the grip by moving the solvent tip around the inner edge of the opening. I did not plug both ends and swish it back and forth (later realize this is a key mistake).I really struggled just to get the end of the grip over the edge of the shaft and then really struggled to get the grip on. All the “goo” from the tape was piling at the end as I pushed. I finally got it, but was risking bending my club head.Attempt 2:I ordered a vise that clamps to a desk because I don’t have a full work bench to mount one too. I mounted it to an old ikea cabinet I didn’t care about and followed a similar technique as Attempt 1. Fail. I got the grip about 2 inches on and it bent and that was it. Trash. I realized the cabinet wasn’t heavy enough to hold my force of pushing, but the key problem was there was still too much friction while trying to push the grip on.Attempt 3: Success (see pic)I moved the cabinet against the wall so I could push as hard as I could. I moved the vise closer to the grip end. I squeezed the black tip of the grip and rolled it to loosen it up in hopes it would get over the end of the shaft easier. Then I plugged the small opening of the grip with my left index finger and poured solvent into the grip by swirling it around the inner edge. Then I plugged the bigger opening of the grip with my right index finger and tilted the solvent in the grip back and forth while spinning it to completely coat the inside of the grip. Then I removed my left index finger and let the solvent drip onto the double sided tape on the shaft to soak it, catching it in a disposable paint tray. I quickly put on the grip, holding the shaft near the vise with my left had while getting the edge of the grip over the edge of the shaft with my right hand. Once on, I used two hands on the grip to push it straight on, and it went in one motion. I don’t need to twist at all. Then, if needed, just slightly straighten by rotating it.Success! I used this process with no issues for the rest of the clubs.I think the keys were loosening the tip of the grip by squeezing it in different directions and then the thorough coating of the inside of the grip by tilting back and forth is critical.Good luck! I almost returned them swearing the inner diameter was too small, but it’s not.

My PGX grip was getting worn out so I decided to use this grip after a golf buddy recommended this. Easy to install and the grip feels great in my hands and is long lasting. It keeps it's tackiness and driver firmly in my hand even when I overswing. Overall nice grip for my PGX driver.

The inside is really soft and damages easily on the metal shaft end. They installed easily at home with my air compressor pressurizing the end during the install, but I struggled to get this installed on my spare set while working on the road without my air compressor, damaged 3 of them.For the cheap price they feel fantastic though, definitely worth it.

I liked the tackiness of the grips.Nice look.I replaced two worn grips on my clubs.Nice not to have to buy a set⛳🌞

I was familiar with this grip so, there were no surprises. Am amazon shipped quickly. All good.

I bought these for my husband as a gift and had them installed by a friend. My husband loves them.

Easy to use

Bought 4 grips, one had a flaw in it and was noticed by the installer, but had no other choice but to install it or purchase a different brand grip.

Nice repair

I wear a large golf glove, so my hands are only a bit bigger than average, but I really like the feel of the jumbo grip. I find I can use a lighter grip pressure both because of the size and stickiness of the grip material. I also really like the shock absorption of the grip material. One thing to bear in mind is that the construction of these grips is similar to a Winn grip. There is a rigid underlisting with the soft grip material wrapped around it. This construction makes these grips a little harder to install because they are not as flexible as a normal grip. I use compressed air to install my grips and I was able to get it on my driver but I had to dip the tip in solvent which I normally don't have to do.

I find these grips great, they have a great feel about them and the grip is non slippery, so great for all weathers, plus the price is very good to.

Excellent grip. Well worth the money. Will review when I play with it in the rain.

use the basic super stroke normally but this one is the next step