LATICRETE SPECTRALOCK PRO Premium® Durable Stain Proof High Performance East to Use Non Sag Epoxy Tile Grout Mini Parts A&B, 2lb

I learned so much from the reviews here I want to pay it forward for all you out there who are thinking about using this Spectralock Premium Pro grout. This stuff is GREAT. What everyone else has said is true, you will be FINE as long as you follow the directions and tips. Have everything ready before you start mixing; and I mean everything – get your sponges, wash water, floats, scale, buckets, rags, microfiber clothes, ice, mixing sticks, scale – EVERYthing together before you start mixing. Mix small batches. For the floor you can do 1:1:6.6; for the walls I did 1:1:6. This works out to 50 grams of Part A, 50 grams of Part B and 330 grams of sand (Part C) for the floors, 300 grams of sand for the walls. It is better to mix too little than too much at a time. It’s not hard to mix and measure, and you won’t get ‘seams’ where different batches meet but it’s expensive and it doesn’t stay workable all that long.I used a plastic kitchen spatula to mix my grout for the floors, a regular epoxy grout float for the floors, a QEP margin float for the walls, and I bought a digital kitchen scale for measuring. I’m including links to these at the end of this review, but I found most of them locally. I mixed the grout in plastic quart sized yogurt containers – but I only mixed the 50:50:300/330 mixture except for when I did the shower floor. My shower floor is 1x1 inch tiles and only 58x32 inches so I mixed a whole Mini set to do that part and used the plastic bucket that the Mini set came in to mix it.Since the colder the grout, the longer it lasts, I put the whole kit in the refrigerator over night before mixing. I also kept the room as cool as I could (I lucked out with the weather so most of the time the room was about 67 degrees) and I also put ice in a bucket and kept the grout in the bucket after I mixed it. The Laticrete website says to dump all the grout out at once, but I didn’t do that – on the floors I spread it out in small batches that I scooped up with the mixing spatula, worked that in and then scooped up another bit. On the walls I scooped it up with the spatula and put it right on the end of the margin float. I got the margin float after trying to use the full-sized float on the walls. My shower wall tiles are 12x24 with 1/16” grout lines and the regular sized trowel was annoyingly large. If your tiles are smaller you probably can just use the regular float.I had grouted once before using regular cement-based grout. If you have grouting experience, the actual grouting is not that different; you have to push a little harder, but otherwise it’s a very similar process. Push it into the grout lines at a diagonal, from both directions and then scrape off the extra with the float at almost 90 degrees.The clean up is the part that you really have to pay attention to. Do your first wash 20-30 minutes after starting your grouting. Get your grout lines the way you like them with this wash. Rinse with plain clean water after you've washed with the solution. If you aren’t going to use the initial wash water again you can use it to wash your grout float and spatula now. If you are going to use the initial wash water again you can clean up your tools with water that has ½-1 cup of vinegar in it. Do a final wash of your tools with soapy water and rinse. Put any extra grout in a zip lock bag, push all the air out and stick it in the freezer for filling in bits and pieces you might have missed or to use later.Your final wash needs to be done 30-60 minutes after your first one. Use a white plastic scrubber (I picked one up in the tile aisle) and the final rinse solution and scrub the tiles in a circular motion. Then use a sponge and the final rinse solution to wipe up the stuff from the tile. Then wipe with plain water. I did the final scrub/wipe/rinse twice. Then on the wall of the shower I used terry cloth rags to wipe the surface dry and then microfiber clothes to polish them (my tile is highly polished porcelain). I did not wear gloves during this final dry/polish phase so I could feel the tile to see if any haze was left on them. Those microfiber clothes are AMAZING.And just as an aside, the Laticrete calculator for determining how much grout you need is very accurate. The shower floor used a LOT of grout since there are so many lines with 1x1 tiles and I kind of freaked out when I saw how much it used and ordered more grout, but I didn’t need it.I hope this helps! Good luck to all – you can do it!!!www.amazon.com/Kitchen-Spatula-Favorite-Utensil-Accessory/dp/B01B3SQF1U/ref=sr_1_28?keywords=Plastic+Spatula&qid=1583679392&s=home-garden&sr=1-28www.amazon.com/MARSHALLTOWN-TROWEL-G02371-Epoxy-Handle/dp/B016TQM7G8/ref=sr_1_3?keywords=marshalltown+epoxy+grout+float&qid=1583679583&s=home-garden&sr=8-3www.amazon.com/QEP-42115Q-42115q-Margin-Float/dp/B00PP3VPXSwww.amazon.com/Ozeri-Professional-Digital-Kitchen-Tempered/dp/B003MSZBSI/ref=sr_1_2_sspa?keywords=kitchen+scale&qid=1583679776&sr=8-2-spons&psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUEyUkZYUlo1NjZaOFJHJmVuY3J5cHRlZElkPUEwODQ5NzIwM1AxWFBWVTAxMEZTUCZlbmNyeXB0ZWRBZElkPUEwNjM2NjY0N0JJSDhDVktFUjVXJndpZGdldE5hbWU9c3BfYXRmJmFjdGlvbj1jbGlja1JlZGlyZWN0JmRvTm90TG9nQ2xpY2s9dHJ1ZQ==

I purchased this grout for a shower floor I am building because I wanted the best possible mold and stain resistance for the “hard service” showers are subject to. I was quite apprehensive before mixing up the grout. Why? Because it’s an epoxy product ... and I would only get one chance to get it right. You can’t temper or tweak the mix with water to adjust the consistency. And I would be on the clock ... no dilly-dally time. I assembled parts A & B and C (the colored ultra fine sand mix). Followed the instructions to the letter ... Mixed A & B thoroughly, added Part C and mixed thoroughly ... and the grout finished to a PERFECT consistency!! and worked into joints that varied from extremely tight to about 1/4” ... although most joints were 1/8”. A smooth ‘epoxy’ grout float is essential, and with a little elbow grease the grout worked easily and perfectly into the joints. Before mixing it appeared as there was no way the milk carton of ultra fine sand would mix properly ... it appeared to be too much dry mix ratio for the epoxy. Nope. The components mixed PERFECTLY to a very workable consistency. I shouldn’t have had ANY apprehension ... this Laticrete epoxy grout kit is bloody PERFECT!And clean-up went perfectly as well. Again, I followed the instructions and cleaned the tile twice, at designated times. The FIRST clean is the serious clean, when I ensured grout buildup was removed from a few tiles that were tipped a bit. My tile was a tumbled travertine, so the grout filled some of the voids and recesses in the tile ... again, perfectly. The sanded grout wasn’t too coarse to fill the voids. I will DEFINATELY use this epoxy mix again ... it was absolutely perfect!! Don’t be apprehensive like me ... follow the instructions and you will get a perfect result. I did.This “mini” kit just barely (but perfectly) grouted my 38” x 42” shower pan with a small, random ‘French’ pattern (photo attached).

I used this for shower pan and curb (its the curb on the left of the pic (NOT the floor on the right). I was concerned with mold mildew and water resistance. All my researched showed that the shower floor fails before anything else. So I did my research and used this product. Very expensive--- but can you put a price on having to redo the grout---even if years later! I was very concerned with the application and how limited my working time was. I found the working time not much shorter than regular grout. I found the cleanup actually much easier. However; you do have to make sure you get it all off the surface or it is almost impossible to remove (not like regular grout where you can almost buff it off later if needed). I did make this mistake so part of my shower pan now is "non skid" like due to the residue. Not a problem in my application but heads up to you. I actually bought the "mini" version first (I was scared to commit!) and then got the full size version to finish.I 100% would use this again in the shower floor. Probably not cost effective to use on walls....

So, first of all the only complain is about Laticrete’s quality control. This set is supposed to be 140 gram of Part A and 140 gram of Part B. The mix requires 1:1:6.5-6.6 proportions of A, B and C respectively. The problem? Not equal volumes. Upon checking weights - Part A had 174 grams in it, and Part B was only 130 grams. So, if anyone would just mix it without checking, they would not get 1:1. Because Part A had more than 44 grams of extra chemical. This is bad business, Laticrete! For the price this grout costs, I expect it to me measured with +/-2 grams tops. The grout itself is good - I needed extra to finish my shower pebbles floor. But I ended up with lesser amount of mix because if mismatch on Laticrete’s side.

I've been using this epoxy grout for 10 plus years for installation in my home and in mosaics. I would not use anything else. This mini size came with the bucket, sponge, cleaner and gloves. Pretty cute, actually.