Replacement Cooler Faucet 2 White and 2 Blue Water Dispenser Tap Set. BPA Free Plastic Spigot..

This review is for the Qboyi Replacement cooler Faucet 2 White and 2 Blue Water Dispenser Tap Set. BPA Free Plastic Spigot. I have an older Brita UltraMax and similar to other reviews, my original spigot had finally completely failed and would no longer allow water to flow when the spigot leaver was moved. I really didn't want to purchase a replacement, so I decided to try fixing mine first. I'm glad I did!Installation is easy, just back off the plastic nut inside the container to allow removal of the old spigot. Then insert this replacement and reinstall with the included washer and nut. Don't over tighten - I did mine to hand tight then used a clean adjustable wrench to go a little more (less than 1/4 turn more).These spigots fit my older Brita UltraMax perfectly and are ALMOST an exact replacement. If you use the usual 'push and hold down' action on the spigot leaver you'll never notice any difference. However, if you like flipping the spigot leaver the opposite direction so that it locks open - you'll find you have to orient the leaver either left or right in order to be able to lift it far enough to lock open. I think this is primarily due to the angle the replacement leaver has vs the OEM. This spigot is just few mm shorter from the exterior nut forward when compared to the OEM, and yet overall it is also a little longer (see pics) as it intrudes farther into the water container than the OEM spigot. Still fits, it's just longer. The replacement spigots included new washers as well.I'm only on day 4 in the frig, but no leaks, no issues and it's great to have water flowing at full velocity again!

Bought this to replace the spigot on my Brita UltraMax Dispenser ("slim" design). The original spigot has begun to slowly leak water at year ~4 and I was unable to permanently fix it or get a replacement from Brita. Scoured Amazon to find 3rd-party replacements that's relatively cheap and had proven reviews.This one fit the bill. Purchased for ~US$6.65 and received 4 as advertised. The length of the neck is a bit longer than the original but was not a huge issue. The diameter I think was slightly smaller than the original but did not affect its function. Plenty of silicone washers so you could add them inside/outside to prevent leaks from both sides. Assembling it is the same as the original. Once cleaned and attached, it functioned perfectly.

It fit perfectly on my water tank. But unfortunately the rubber ring did not seal the water in. There was a tiny amount of water leaking, had to use the old rings, inside and out. The rings need to be thicker. It all worked in the end and we got spare ones for a good price.

I bought these faucets for installation on an old plastic ice cooler and on a liquid laundry detergent dispenser, as described below. Installation is eazy. Once you have the properly sized hole, insert the main body with the threaded pipe through the hole, and secure it using the included nut and washers. You might want to take the additional step of using a hacksaw or other implement to remove any excess threaded pipe, which might become a nuisance.I bought a large jug of laundry detergent with a push-button faucet on the side. The detergent was so-so but I liked the convenient faucet. The problem with that push-button faucet was that it was very stiff and took a while for an adequate amount of the normally thick liquid detergent to be dispensed. That was a minor issue in the larger scheme, but one of these faucets relieved me of the anxiety of having to hold that stiff faucet button down every time I loaded the washing machine. :-)The old faucet was mounted on a screw lid, which made replacing it a breeze. I now refill the jug with a detergent of my choice and only need to flip the faucet handle and wait for the desired amount of detergent to be dispensed. The replacement faucet takes about the same amount of time to dispense, but it's no longer necessary to hold down that very stiff push-button. (This is a reminder to stop and smell the roses from time to time, and appreciate the little things.)These simple flip-handle faucets worked for my applications, and I'm confident they would work well on your ice coolers and for other purposes. I recommend them without reservation.Note: I suggest you do a little bit of homework before your purchase. Make sure the faucet will fit the final install location and that you have the tools and access to make the install.

Easy to i stall and worked well brita dispenser.

Exactly what I was looking for (for days and days... online and locally). Good details in description including precise item measurements. All the 'parts' needed were included in order including 2 gaskets for each spigot. Arrived super fast in perfect condition.

Replaced the Brita UltraMax OEM spigot. I bought the 2 blue and 2 white spigot, 4 pack, with washers included. It fits fairly well. I installed it with a single washer on the outside of the reservoir (It has enough washers included to have both a washer inside and outside of the reservoir for all four spigots).It doesn't leak, seals and works well. Water flow is good. I washed and cleaned the entire water dispenser before installing the new spigot. I Love it and I'm glad to have three additional replacements with washers, as we also have a Brita XL Water dispenser that may need replacing one day.Just a side note; The UltraMax OEM spigot has a single white washer, located on the inside of the reservoir. It eventually ended up with a horrendous mildew like smell, and it transfered to the water in both taste and smell. There was no indication of mildew on the washer or why it smelled terrible. It took me several cleanings of the entire despencer to find that the washer was the problem. The OEM spigot actually still works, but I just wanted to replace the entire spigot assembly, rather than just the rubber washer. Anyway, I just thought I'd share this, incase anyone else has this problem.