(Ship from USA) Genuine Consew CSM1000 Servo Sewing Machine Motor 3/4HP CS1000 CSM550 SM550-1PLKHG484UY5151

This Consew CSM1000 servo motor was shipped with the improved C1000 controller. This controller (note 4 buttons and 4 digit display), allows the easy setting of the maximum speed using the + or - buttons. Setting U4 allows the setting of the ramp up speed (starts slow and then speeds up).This 2 piece unit is easy to mount , and the controller can be mounted at an convenient location for quick access to power and speed controls.The servo motor weighs approximately 30# less than the old clutch motor previously mounted on my table.The installation photo show the motor installed on a treadle base, giving it a dual power capability.Operation has been flawless. I used the recommended 45mm Yeqin replacement pulley for better power and lower speed. .. the only drawback to this item is the limited operating and installation instructions.

Holy cow! This is so much better than using a clutch motor. And really quiet .I used it with a Consew 225 and it was so easy to install. Highly recommend!

I love this servo motor much more than the clutch motor it replaced. It only weigs about 5 lbs and replace the old mother weighing about 50 lbs One of the reviews stated it would go from zero to 4500 rpm, but that is incorrect. It can be set as low as 500 rpm and as high as 4500. When set to something, the pedal will start it and some more pedal goes a little faster. I never tried the pully that came with it as I also ordered a 45 mm pully at the same time. For installation, find a video online as it comes with no instructions. A peeve of mine is that I thought I was ording the Consew brand when in fact it just the same unit as others that are lower priced. I could have saved $30 by just ording from a different vendor. Still happy with the purchase though.

Bought this for my mothers Singer 251-12 lock-stitch, her "go to" machine. She was a professional tailor/seamstress for over 35 years and has had some high end clients and done all sorts of crazy projects (till she retired having her own business) and always used a clutch motor. She has one of those "if it works, don't fix it" attitudes. I installed this as a surprise for her and she has zero regrets dumping the clutch motor. For her application I had to get a 40 inch belt which was smaller than what the old motor used (yours might vary). The motor was a direct bolt in, just had to trim one of the carriage bolts to clear the motor. She says she has a lot more control over the machine at low speeds, it also sews a lot faster than the clutch motor, and not having to hear the constant noise of the clutch motor is a huge plus. Hope this helps someone with their decision. If there are any problems, I'll post them here.

My motor arrived at 3:16. It is 4:49, and I have just finished sewing off on garment leather, nylon webbing, and 9-10 oz Latigo. The time includes testing the motor before I installed it, removing the old motor of course, and I have never installed a motor before (always bought full packages, assembled and delivered).So as a total motor neophyte (but pretty good with tools), and zero instructions on mounting included, it is humming (well, not humming!) along and performing far better than my expectations. Everything fit in perfectly, bolts all reached where they should, and the linkage has more than enough adjustment for my machine (Consew 206RB). A socket and crescent wrench set (you can skip the socket, but it does save some time), a Phillips screwdriver, and, preferably an electric drill for pilot holes, is all you need. The holes in the table aligned perfectly, and you only have to install two screws in a new spot for the control box.The machine chugs a bit on the heavy leather, but it never stalled, even at a very slow speed. Ramp the speed up a bit and it sews that leather as well as did my clutch motor.One tiny nit to pick, I would much rather have a dial speed adjustment than the push button. I would be sewing the leather slowly, but the nylon much faster, and I switch back and forth a lot, so the button pressing (or pressing and holding, and holding, and holding) is going to get old. But for the price, and quiet (that is SO nice) and the performance at this price, I'll push a button.As one other person said, don't think about it, just buy it. If you're on a clutch motor it is like you just left the stone age.More info: I have had this in daily operation for about two months. It still performs flawlessly, and my electric bill seems to have dropped about $7.00 a month, and I cannot attribute it to anything other than not having a clutch motor going all day. So, in a couple of years, this will have been free!

The media could not be loaded. Much better speed control, easy to reverse, quiet, lightweight, such an upgrade. But broke after just a couple months. Left a message with support — if they can help me fix it / repair it will update with a better review.

Recently converted from a clutch motor to this servo motor. I put this on my industrial Pfaff Eco 45 for sewing leather. There wasn't any instructions so it took a while trying to figure out where all the pieces go. There were a couple of bolts, nuts, and washers that weren't used and have no idea where they go. I like the ability to slow the motor down, I just wish you could go even slower. Sometimes with leather, you need to go very slow. The lowest setting is 500, it would be nice if it could go to 100. The highest setting is 4500. So I assume that it's 500 rpms or 4500 rpms. Overall, a good value if you need to swap out your motor for your sewing machine.