JDMSPEED New Universal Electric Power Window Lift Regulator Conversion Kit with Switches Wiring and Hardware for 2 Door Pickup SUV Truck Van Car

This is very easy to install. Just remember 2 things: 1) The instructions are worthless. Watch one of the youtube videos. 2) Place the motor over one of the numerous holes in the door. Then make sure the side that sticks out goes into the hole and not in the way of the door panel going back on. I taped the wires to a stiff wire to feed them through the channel in the door, through the rubber tube and into the vehicle. For power I had to run it to the fusebox under the hood. Under the dash fuses all had continuous power - And this has constant power feed so it could kill your battery if it is always on. As long as I had the panels off I replaced the door speakers. Easy to do since the panel was off. This is much slower than oem, and with the vehicle not started the windows barely made it up. I lubricated the tracks and cleaned the windows with pledge furniture polish to help them go up. The 15 to 20% higher voltage when the vehicle was running helped a lot.

Just installed it on my cargo van and it’s working 100% like if it came from factory with it.

Bought an 89 Silverado for my son who is turning 16 soon and wanted it to have power windows and locks. Installed them both at the same time so took a while. I searched YouTube and found a video with a similar model but not exactly the same but was helpful enough to install it as there are no real instructions that come with the kit. I would suggest watching the video first to get an idea of what it takes to install it. I installed everything and ran the wiring and got everything working. I then went to put the door panel back on and there was not room where the armrest goes over the motor. I ended up cutting off a small ledge from the door on both sides so I could move the motor up higher to allow for clearance so the armrest would go over the motor. I would suggest trying to get the motor lined up where you think it will work and then see if the door panel will go over the motor.Wiring is pretty straightforward if you are somewhat electrically inclined. I ran power to a higher amp fuse in the fuse box that will be on when truck is running or accessory. The power wire has an inline 30 amp fuse. The motors work well and raise and lower the windows quickly. They are not overly loud either. The only issue that I currently have is that sometimes the button for the passenger side that is on the drivers side is not always lit. It still functions but the backlit light comes and goes. Not a big deal as it still works as it should. I am not sure if it is the switch or if there is something else wrong.I am pleased with the kit so far and as other reviews have stated time will tell on how long the motors will last. The good thing is that the kits are not overly expensive and as long as they make the same kit in the future, it should be an easy swap out of the motors. I would also suggest if your are installing on an older vehicle, maybe order some new door panel retainer clips. I had a few missing and the others were fairly brittle. I ordered some on Amazon that I am going to replace most of the clips. You can get 50 of them for under $10.I would recommend this kit to anyone looking to get power windows in a vehicle with manual windows.

I read the reviews before I bought this and decided to get it anyway. A couple of the reviews mentioned stripping of the plastic adapters and a burning and melting of electrical wires. My experience with these issues are as follows; Stripping of the adapters - when I tried using the tightest, most snug fitting adapters and powered the windows up and down a few times and at the end of the window travel the motor would continue to turn when the crank could no longer turn as the window was either all the way up or all the way down and eventually stripping the adapter that fits over the window crank. The solution is to use the best fitting adapter, one that you don't have to force on that has very slight play on the window crank, the window will roll up and down smoothly and will positively stop in the maximum up or down position.The burning wires. As I was installing the power windows I would test them occasionally throughout the process, I had the ground wire connected and I would hold the positive wire to a positive lead with my fingers to operate the window. While doing this I could feel the wire getting hot so I looked around to see what's causing this then noticed the wires to the other window wasn't hooked up yet and were making contact with each other, I separated the wires and insulated them and tried again and wires stopped getting hot. It could also be because the installer didn't pay attention to the 2 brown wires in the harness, one of the brown wires has a red stripe on it, easy to miss and connect it to the wrong position in the connector plug if your not paying attention.I really like it and my advise to anyone who's going to install one of these is take your time, don't rush it, it is a universal kit and installations will vary in the ease, time and by the skill of the installer.

I purchased this in January, relatively easy install. Little over a month later one of my motors went out. I understand this happens. Got ahold of Amazon which they connected me with the company. Explained the problem, took pictures, and they had no problem sending me another. This is where the company went above and beyond. FedEx supposedly delivered my package but the confirmation picture was a picture of rocks which brings me to believe they have a shady carrier. I tried to put in a claim but FedEx said the company had to do it on their end. Reached out to Jdmspeed and they tried to find my package with no luck. Without it not being either of our faults they still sent me another replacement. Awesome job Jdmspeed! Would definitely do business with them again and recommend them to others!

I installed these about 1 month ago, passenger side motor slowly got slower on up and down activation to the point where it is almost dead and I will have to remove. Drivers side works perfectly so it has to be defective motor or overall quality issue.

Works on my '99 F450. Very easy to install and seems to be working so far. Will update if I have issues with it